Poulan XT24H48YT manual To Replace Mower Blade Secondary Drive Belt See Fig

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE (SECONDARY) DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake.

Remove mower (See “TO REMOVE MOWER” in this section of manual).

Remove screws from R.H. and L.H. mandrel covers and remove covers.

REMOVE MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Carefully roll belt over the top of R.H. mandrel pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

REMOVE MOWER BLADE (SECONDARY) DRIVE BELT

Carefully roll belt off L.H. mandrel pulley.

Remove belt from center mandrel pulley, idler pulley, and R.H. mandrel pulley.

Remove any dirt or grass which may have accumulated around mandrels and entire upper deck surface.

Check secondary idler arm and idler pulley to see that they rotate freely.

Be sure spring is hooked in secondary idler arm and secondary spring arm.

INSTALL NEW MOWER BLADE (SECONDARY) DRIVE BELT

Install new belt in lower groove of R.H. mandrel pulley, idler pulley, and center mandrel pulley as shown.

Carefully roll belt over L.H. mandrel pulley. Make sure belt is in all grooves properly.

REINSTALL MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Install belt into upper groove of R.H. mandrel pulley and around both idlers. Pull belt to front of mower to remove slack.

Reinstall mandrel covers and securely tighten all screws.

Carefully check belt routing making sure belt is in all grooves correctly.

Reinstall mower to tractor (See “TO INSTALL MOWER” in this section of manual).

 

SECONDARY

SPRING

L.H. MAN-

IDLER ARM

IDLER

SECONDARY

DREL

 

PULLEY

SPRING ARM

 

 

CENTER

 

 

MANDREL

 

R.H. MANDREL

FIG. 23

TO CHECK AND ADJUST BRAKE (See Fig. 24)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

Depress clutch/brake pedal all the way down and en- gage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

23

Image 23
Contents Always Wear EYE Protection During Operation XT24H48YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Before Starting the EngineTo Transport See Figs Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Before Each USE MaintenanceLubrication Chart General RecommendationsCheck Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation To Replace Motion Drive Belt See FigTo Attach Jumper Cables Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

XT24H48YT specifications

The Poulan XT24H48YT is a robust riding lawn mower, designed to tackle a variety of mowing tasks with efficiency and ease. This model is particularly well-suited for homeowners with medium to large yards, offering impressive power and maneuverability to get the job done effectively.

At the heart of the XT24H48YT is a dependable 24-horsepower Briggs & Stratton engine. This powerful engine provides the durability and reliability necessary for consistent performance over time. The engine is coupled with a hydrostatic transmission, which allows for smooth, automatic speed adjustments without the need for manual shifting. This feature enhances the overall ease of operation, particularly in larger or more complex terrains.

The cutting deck on the Poulan XT24H48YT measures 48 inches in width, which strikes an excellent balance between efficient grass cutting and ease of navigation in tighter spaces. The deck features a reinforced design, enabling it to withstand the rigors of frequent use. Additionally, the mower comes equipped with a cutting height adjustment feature that allows users to customize their mowing height across six different positions, ensuring the best results for various grass types and conditions.

One of the standout features of the Poulan XT24H48YT is its ergonomically designed seat and controls. The high-back seat offers ample support and comfort during extended mowing sessions, while the user-friendly steering system contributes to easy handling and maneuverability. The mower also includes a tight turning radius, allowing users to navigate around landscaping obstacles and corners with ease.

In terms of additional technologies, the Poulan XT24H48YT sports a variety of practical features such as a built-in headlight for improved visibility during early morning or late evening mowing. Furthermore, the model has a durable outer chassis constructed from high-quality materials, ensuring it can withstand the elements and rough terrains.

Maintenance is made simpler with the addition of an easy-access hose connection for cleaning the cutting deck, helping to keep the mower in excellent condition without extensive effort. The Poulan XT24H48YT is also compatible with various lawn care accessories, providing versatility and the ability to adapt the machine to different seasonal tasks.

Overall, the Poulan XT24H48YT combines power, comfort, and versatility, making it a compelling choice for homeowners seeking an effective riding lawn mower that can handle a variety of mowing tasks with ease. Its thoughtful design and features ensure that lawn care remains a manageable and pleasant chore.