Poulan PXT12530 manual Tractor, Blade Care, Blade Removal See Fig, Brake Operation, Tires

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 13)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results, mower blade must be kept sharp. Replace bent or damaged blade.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 14)

•Raise mower to highest position to allow access to blade.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

Fig. 14

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 13

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PXT12530 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly ToremovetractorfromcartonCheck Brake System Install Seat See FigOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged To SET Parking Brake See FigReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System To Move Forward and Backward See FigBefore Starting the Engine To Start Engine See Fig Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBrake Operation TractorBlade Care Blade Removal See FigBelts BatteryTransaxle Maintenance EngineMuffler CleaningClean AIR Screen AIR FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine continues Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty

PXT12530 specifications

The Poulan PXT12530 is a robust and versatile string trimmer designed for homeowners and landscapers who value efficiency and power in their gardening tools. This model boasts an array of features and technologies that make it a standout choice for tackling both small and large yard maintenance tasks.

One of the main features of the Poulan PXT12530 is its lightweight design. Weighing in at a mere 12 pounds, this string trimmer is easy to maneuver, reducing fatigue during extended use. The trimmer also features a curved shaft, which enhances control and provides a comfortable grip, allowing users to reach tight spaces and navigate around obstacles with ease.

Powering the PXT12530 is a dependable 25cc two-cycle engine that delivers ample power for various trimming tasks. This engine ensures that users can tackle overgrown grass and weeds without straining the equipment. The trimmer is equipped with a centrifugal clutch that engages the cutting head only when the throttle is pulled, enhancing safety and improving user control.

Another notable characteristic of the Poulan PXT12530 is its dual-line cutting system. This feature allows for a wider cutting swath, effectively reducing the time needed to complete trimming tasks. The trimmer head is designed to accept .065-inch line, making reloading quick and straightforward. Additionally, it comes with a bump feed mechanism, which automatically feeds more line with a simple tap on the ground, providing convenience and efficiency while you work.

The PXT12530 also emphasizes user comfort through its anti-vibration technology. This system significantly reduces vibrations during operation, making it more comfortable for the user and helping to maintain focus during prolonged use. Coupled with its adjustable handle, the trimmer enables personalized adjustments to suit different user heights, promoting ergonomic handling.

Durability is another key aspect of the Poulan PXT12530. Constructed with high-quality materials, this trimmer is built to withstand the demands of regular use. The protective guards around the cutting head not only enhance safety but also minimize wear and tear.

In conclusion, the Poulan PXT12530 combines practicality, power, and user-friendly features, making it an excellent choice for anyone looking to maintain their yard efficiently. Its lightweight design, powerful engine, dual-line system, and comfort features all contribute to an impressive performance, setting it apart in the realm of string trimmers. Whether you're tackling routine lawn maintenance or preparing your yard for a special occasion, the PXT12530 is a reliable companion that gets the job done effectively.
Top Page Image Contents