Poulan PXT12530 manual Tools Required for Assembly, Toremovetractorfromcarton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

LABEL

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

BOLT

LOCK

WASHER

LARGE

FLAT WASHER

STEERING

WHEEL

STEERING

BOOT

ADAPTER

TABS

EXTENSION SHAFT

TAB

SLOTS

LOWER STEERING

SHAFT

03132

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PXT12530 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations MaintenanceMaintenance ScheduleBlade Removal See Fig TractorBlade Care Brake OperationEngine BatteryTransaxle Maintenance BeltsAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Remove Wheel See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty

PXT12530 specifications

The Poulan PXT12530 is a robust and versatile string trimmer designed for homeowners and landscapers who value efficiency and power in their gardening tools. This model boasts an array of features and technologies that make it a standout choice for tackling both small and large yard maintenance tasks.

One of the main features of the Poulan PXT12530 is its lightweight design. Weighing in at a mere 12 pounds, this string trimmer is easy to maneuver, reducing fatigue during extended use. The trimmer also features a curved shaft, which enhances control and provides a comfortable grip, allowing users to reach tight spaces and navigate around obstacles with ease.

Powering the PXT12530 is a dependable 25cc two-cycle engine that delivers ample power for various trimming tasks. This engine ensures that users can tackle overgrown grass and weeds without straining the equipment. The trimmer is equipped with a centrifugal clutch that engages the cutting head only when the throttle is pulled, enhancing safety and improving user control.

Another notable characteristic of the Poulan PXT12530 is its dual-line cutting system. This feature allows for a wider cutting swath, effectively reducing the time needed to complete trimming tasks. The trimmer head is designed to accept .065-inch line, making reloading quick and straightforward. Additionally, it comes with a bump feed mechanism, which automatically feeds more line with a simple tap on the ground, providing convenience and efficiency while you work.

The PXT12530 also emphasizes user comfort through its anti-vibration technology. This system significantly reduces vibrations during operation, making it more comfortable for the user and helping to maintain focus during prolonged use. Coupled with its adjustable handle, the trimmer enables personalized adjustments to suit different user heights, promoting ergonomic handling.

Durability is another key aspect of the Poulan PXT12530. Constructed with high-quality materials, this trimmer is built to withstand the demands of regular use. The protective guards around the cutting head not only enhance safety but also minimize wear and tear.

In conclusion, the Poulan PXT12530 combines practicality, power, and user-friendly features, making it an excellent choice for anyone looking to maintain their yard efficiently. Its lightweight design, powerful engine, dual-line system, and comfort features all contribute to an impressive performance, setting it apart in the realm of string trimmers. Whether you're tackling routine lawn maintenance or preparing your yard for a special occasion, the PXT12530 is a reliable companion that gets the job done effectively.
Top Page Image Contents