Poulan PXT12530 manual To Level Mower, Visual SIDE-TO-SIDE Adjustment See Fig

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 25)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

Fig. 25

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 26)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 26

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 27 & 28) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 3/8" lower than the rear tip when the mower is in its highest position.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 27

•If front tip of blade is not 1/8" to 3/8" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 28

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 3/8" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PXT12530 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig Using the Reverse Operation SystemTo Move Forward and Backward See Fig Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance MaintenanceGeneral Recommendations ScheduleTractor Blade CareBlade Removal See Fig Brake OperationBattery Transaxle MaintenanceEngine BeltsCleaning Clean AIR ScreenAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty

PXT12530 specifications

The Poulan PXT12530 is a robust and versatile string trimmer designed for homeowners and landscapers who value efficiency and power in their gardening tools. This model boasts an array of features and technologies that make it a standout choice for tackling both small and large yard maintenance tasks.

One of the main features of the Poulan PXT12530 is its lightweight design. Weighing in at a mere 12 pounds, this string trimmer is easy to maneuver, reducing fatigue during extended use. The trimmer also features a curved shaft, which enhances control and provides a comfortable grip, allowing users to reach tight spaces and navigate around obstacles with ease.

Powering the PXT12530 is a dependable 25cc two-cycle engine that delivers ample power for various trimming tasks. This engine ensures that users can tackle overgrown grass and weeds without straining the equipment. The trimmer is equipped with a centrifugal clutch that engages the cutting head only when the throttle is pulled, enhancing safety and improving user control.

Another notable characteristic of the Poulan PXT12530 is its dual-line cutting system. This feature allows for a wider cutting swath, effectively reducing the time needed to complete trimming tasks. The trimmer head is designed to accept .065-inch line, making reloading quick and straightforward. Additionally, it comes with a bump feed mechanism, which automatically feeds more line with a simple tap on the ground, providing convenience and efficiency while you work.

The PXT12530 also emphasizes user comfort through its anti-vibration technology. This system significantly reduces vibrations during operation, making it more comfortable for the user and helping to maintain focus during prolonged use. Coupled with its adjustable handle, the trimmer enables personalized adjustments to suit different user heights, promoting ergonomic handling.

Durability is another key aspect of the Poulan PXT12530. Constructed with high-quality materials, this trimmer is built to withstand the demands of regular use. The protective guards around the cutting head not only enhance safety but also minimize wear and tear.

In conclusion, the Poulan PXT12530 combines practicality, power, and user-friendly features, making it an excellent choice for anyone looking to maintain their yard efficiently. Its lightweight design, powerful engine, dual-line system, and comfort features all contribute to an impressive performance, setting it apart in the realm of string trimmers. Whether you're tackling routine lawn maintenance or preparing your yard for a special occasion, the PXT12530 is a reliable companion that gets the job done effectively.
Top Page Image Contents