Poulan Pro 900 ZX manual Checking the V-belts, Deck belt

Page 44

MAINTENANCE

Checking the V-belts

WARNING!

No adjustments or maintenance to be carried out unless:

The engine is stopped.

The ignition key has been removed.

The parking brake is on.

Deck belt

V-belts are not adjustable. Replace belts if they begin to slip from wear.

Deck belt removal

WARNING!

Idler arm is spring loaded. Have a tight grip on idler arm or ratchet and release slowly.

Park on a level surface. Apply parking brake.

Lower the deck into the lowest cutting position

Disengage belt tension by pushing inward on deck belt idler pulley by hand or with a 1/2” drive ratchet placed in square drive hole on idler arm, While arm is pushed inward, remove belt from stationary idler pulley and release idler arm slowly until spring force is no longer felt.

Remove bolt from idler pulley. This will allow belt to pass by the belt guide.

Loosen screws from both left and right plastic belt shield above each mandrel housing. Remove shields

Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.

Carefully roll the belt over the top of the cutter housing pulleys.

Remove the belt from around the electric clutch on the engine shaft.

The belt can now be removed.

English-42

Image 44
Contents Pro 900 ZX Page Contents OPERATOR’S Manual Rider SeriesEnglish-2 Introduction IntroductionGood Service Manufacturing NumberXxxx xxxxxx Symbols and DecalsSymbols and Decals Objects Engine is Running Moving sharp blades under cover General Operation Safety InstructionsSafety Instructions English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Risk of sparking Transport Important InformationCustomer responsibilities Control Locations ControlsControls Motion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingThrottle Control Ignition SwitchChoke Control Machine must be stopped before activating the parking brake Hour MeterParking Brake Accessories Cutting height pedalTraining OperationOperation Before Starting Starting the EngineDepress the control for disengaging the mower deck Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance Schedule MaintenanceMaintenance = Described in this manual  = Not described in this manual Battery To clean battery and terminalsReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Replacing the Air Filter Briggs and Stratton engineFaulty adjustment can cause an accident Replacing the Fuel FilterChecking Tire Pressures Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation EZT belt removal EZT beltTo replace EZT E-Series Zeroturn Transaxle belt Checking the Blades Check the bladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingCaster Wheels HardwareLubrication Schedule LubricationLubrication Lubricating the Cables Lubricating in Accordance with the Lubrication ScheduleCaster wheels Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Changing the Oil FilterTransmission Problem Cause Trouble Shooting GuideTrouble Shooting Guide Wrong fuel type English-58 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramZ4822 Technical DataTechnical Data Equipment Torque Specifications USA requirements Conformity CertificatesConformity Certificates Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-68 English-69 English-70 At Least Once Each Year English-72 English-73 110192Rir12/19/05