Poulan Pro 900 ZX manual Adjusting the Mower Deck

Page 48

MAINTENANCE

•Install new or re-sharpened blade with stamped "GRASS SIDE" facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing.

•Install and tighten blade bolt securely.

Torque blade bolt to 45-55 ft/lb (61-75 Nm).

IMPORTANT INFORMATION Special blade bolt is heat treated. Replace with a Husqvarna bolt if required.

Do not use lower grade hardware than specified.

Adjusting the Mower Deck

WARNING!

Before performing any service or adjustment checklist: 1. Engage the parking brake.

2.Place the Blade-switch in the disengaged position.

3.Turn ignition switch to “OFF” position and remove the key.

4.Make sure the blades and all moving parts have completely stopped.

5.Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.

WARNING!

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

Check the tire pressure before adjustment of the mower deck, see “Checking Tire Pressure” in Maintenance section.

Faulty mower deck adjustment will cause an uneven mowing result.

English-46

Image 48

Contents Pro 900 ZX Page Contents OPERATOR’S Manual Rider SeriesEnglish-2 Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxx xxxxxx Objects Engine is Running Moving sharp blades under cover Safety Instructions Safety InstructionsGeneral Operation English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Risk of sparking Transport Important InformationCustomer responsibilities Controls ControlsControl Locations Motion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingIgnition Switch Choke ControlThrottle Control Hour Meter Parking BrakeMachine must be stopped before activating the parking brake Accessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDepress the control for disengaging the mower deck Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual Battery To clean battery and terminalsReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableChecking the Engines Cooling Air Intake Replacing the Air Filter Briggs and Stratton engineFaulty adjustment can cause an accident Replacing the Fuel FilterChecking Tire Pressures Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation EZT belt To replace EZT E-Series Zeroturn Transaxle beltEZT belt removal Checking the Blades Check the bladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingCaster Wheels HardwareLubrication LubricationLubrication Schedule Lubricating the Cables Lubricating in Accordance with the Lubrication ScheduleCaster wheels Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Changing the Oil FilterTransmission Trouble Shooting Guide Trouble Shooting GuideProblem Cause Wrong fuel type English-58 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZ4822 Equipment Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-68 English-69 English-70 At Least Once Each Year English-72 English-73 110192Rir12/19/05