Poulan PR1842STC To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR1842STC IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Contents of Hardware Pack Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine ADD GasolineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsBefore Each USE Tractor Engine Cleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing To Replace Mower Blade Drive Belt See FigTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysOther Fuel SystemEngine OIL CylindersTroubleshooting Points OFF Schematic Tractor - Model Number PR1842STCElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR1842STC specifications

The Poulan PR1842STC is a powerful and versatile riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. With its robust engineering and user-friendly features, the PR1842STC stands out among its competitors, making it an ideal choice for maintaining larger yards with ease.

One of the keynote features of the PR1842STC is its 18.5 horsepower Briggs & Stratton engine. Known for its durability and easy starting capabilities, this engine provides ample power to handle tough mowing tasks, ensuring a clean cut even in challenging conditions. The mower’s automatic transmission allows for smooth operation, enabling users to easily adjust their speed without the hassle of shifting gears manually.

The PR1842STC boasts a 42-inch cutting deck, which strikes a perfect balance between maneuverability and cutting width. This size is particularly advantageous for homeowners with medium to large lawns, as it allows for efficient mowing while still being able to navigate through tighter spots. The cutting deck features three adjustable positions, giving users the flexibility to choose their desired grass height from 1 to 4 inches.

Equipped with a front bumper and reinforced deck, the PR1842STC is built to withstand the rigors of regular lawn maintenance. The mower also incorporates a comfortable high-back seat, providing additional support for those longer mowing sessions, and an ergonomic steering wheel designed for ease of handling. An essential feature is the cutting height adjustment lever located conveniently near the operator's seat, allowing for quick changes on the fly.

One of the most notable technologies integrated into the PR1842STC is its easy-starting system, designed to ensure reliability on the first pull. Furthermore, the mower features a reliable mulching system, allowing users to finely chop grass clippings to enhance lawn health and minimize waste.

Safety is a priority for Poulan, and the PR1842STC includes several safety features. These include an automatic shut-off system that engages when the operator leaves the seat, ensuring that the mower stops safely to prevent accidents.

Overall, the Poulan PR1842STC is a well-rounded riding lawn mower that combines power, user-friendly design, and advanced features, making it an excellent investment for those serious about lawn maintenance. Whether tackling tall grass or navigating tricky terrain, the PR1842STC delivers robust performance for a beautifully manicured lawn.
Top Page Image Contents