Poulan PR1842STC owner manual Before Starting the Engine, ADD Gasoline, Check Engine OIL Level

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

To change engine oil, see the Customer Responsibili- ties section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: When operating in temperatures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sepa- ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

Place gear shift lever in neutral (N) position.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke () position and retry.

WARM WEATHER STARTING (50° F and above)

When engine starts, move the throttle control to the fast position.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

When engine starts, allow engine to run with the throttle

control in the choke () position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tempera- ture.

The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Image 13
Contents PR1842STC Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Contents of Hardware Pack HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Convert to Bagging or DISCHARG- ING To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Tractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Remove Mower See Fig To Install Mower See FigTo Replace Mower Blade Drive Belt See Fig To Level Mower HousingTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersTroubleshooting Points OFF Tractor - Model Number PR1842STC SchematicElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

PR1842STC specifications

The Poulan PR1842STC is a powerful and versatile riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. With its robust engineering and user-friendly features, the PR1842STC stands out among its competitors, making it an ideal choice for maintaining larger yards with ease.

One of the keynote features of the PR1842STC is its 18.5 horsepower Briggs & Stratton engine. Known for its durability and easy starting capabilities, this engine provides ample power to handle tough mowing tasks, ensuring a clean cut even in challenging conditions. The mower’s automatic transmission allows for smooth operation, enabling users to easily adjust their speed without the hassle of shifting gears manually.

The PR1842STC boasts a 42-inch cutting deck, which strikes a perfect balance between maneuverability and cutting width. This size is particularly advantageous for homeowners with medium to large lawns, as it allows for efficient mowing while still being able to navigate through tighter spots. The cutting deck features three adjustable positions, giving users the flexibility to choose their desired grass height from 1 to 4 inches.

Equipped with a front bumper and reinforced deck, the PR1842STC is built to withstand the rigors of regular lawn maintenance. The mower also incorporates a comfortable high-back seat, providing additional support for those longer mowing sessions, and an ergonomic steering wheel designed for ease of handling. An essential feature is the cutting height adjustment lever located conveniently near the operator's seat, allowing for quick changes on the fly.

One of the most notable technologies integrated into the PR1842STC is its easy-starting system, designed to ensure reliability on the first pull. Furthermore, the mower features a reliable mulching system, allowing users to finely chop grass clippings to enhance lawn health and minimize waste.

Safety is a priority for Poulan, and the PR1842STC includes several safety features. These include an automatic shut-off system that engages when the operator leaves the seat, ensuring that the mower stops safely to prevent accidents.

Overall, the Poulan PR1842STC is a well-rounded riding lawn mower that combines power, user-friendly design, and advanced features, making it an excellent investment for those serious about lawn maintenance. Whether tackling tall grass or navigating tricky terrain, the PR1842STC delivers robust performance for a beautifully manicured lawn.