Poulan PR1842STC owner manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 17

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instructions.

20

Image 20
Contents PR1842STC IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Contents of Hardware Pack Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine ADD GasolineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Engine Cleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysOther Fuel SystemEngine OIL CylindersTroubleshooting Points OFF Schematic Tractor - Model Number PR1842STCElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR1842STC specifications

The Poulan PR1842STC is a powerful and versatile riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. With its robust engineering and user-friendly features, the PR1842STC stands out among its competitors, making it an ideal choice for maintaining larger yards with ease.

One of the keynote features of the PR1842STC is its 18.5 horsepower Briggs & Stratton engine. Known for its durability and easy starting capabilities, this engine provides ample power to handle tough mowing tasks, ensuring a clean cut even in challenging conditions. The mower’s automatic transmission allows for smooth operation, enabling users to easily adjust their speed without the hassle of shifting gears manually.

The PR1842STC boasts a 42-inch cutting deck, which strikes a perfect balance between maneuverability and cutting width. This size is particularly advantageous for homeowners with medium to large lawns, as it allows for efficient mowing while still being able to navigate through tighter spots. The cutting deck features three adjustable positions, giving users the flexibility to choose their desired grass height from 1 to 4 inches.

Equipped with a front bumper and reinforced deck, the PR1842STC is built to withstand the rigors of regular lawn maintenance. The mower also incorporates a comfortable high-back seat, providing additional support for those longer mowing sessions, and an ergonomic steering wheel designed for ease of handling. An essential feature is the cutting height adjustment lever located conveniently near the operator's seat, allowing for quick changes on the fly.

One of the most notable technologies integrated into the PR1842STC is its easy-starting system, designed to ensure reliability on the first pull. Furthermore, the mower features a reliable mulching system, allowing users to finely chop grass clippings to enhance lawn health and minimize waste.

Safety is a priority for Poulan, and the PR1842STC includes several safety features. These include an automatic shut-off system that engages when the operator leaves the seat, ensuring that the mower stops safely to prevent accidents.

Overall, the Poulan PR1842STC is a well-rounded riding lawn mower that combines power, user-friendly design, and advanced features, making it an excellent investment for those serious about lawn maintenance. Whether tackling tall grass or navigating tricky terrain, the PR1842STC delivers robust performance for a beautifully manicured lawn.