Poulan 952802062 Bucking Without a Support, Bucking Using a LOG or Support Stand, Limbing

Page 13

until the saw can be removed easily. Restart the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting

Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

SOvercut through 1/3 of the diameter of the

log.

SRoll the log over and finish with a second overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR SUPPORT STAND

SRemember your first cut is always on the compression side of the log.

(Refer to the illustrations below for your first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support 2nd Cut

1st Cut

1st Cut

2nd Cut

Using a support stand 2nd Cut

1st Cut

1st Cut

2nd Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, plat- forms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure footing and balance.

SWatch out for springpoles. Springpoles are

small size limbs which can catch the saw chain and whip toward you or pull you off bal- ance. Use extreme caution when cutting small size limbs or slender material.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop- erly.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderTions found in this manual Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 If your hand slips off the front handlebarAttaching the BAR & Chain If not AssemblyChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW CHOKE/FAST Idle Lever Throttle LOCK-OUTPrimer Bulb Chain BrakeStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCheck Guide BAR Check Fuel Mixture LevelChain Adjustment Cleaning the Spark ARREST- ING ScreenReplace Spark Plug Chain SharpeningIdle Speed-T Carburetor AdjustmentCooling System RightSeasonal Storage StorageFuel System EngineEmpty fuel tank and refill with Load Adjustment EngineLigations The U.S. Environmental Poulan PRO

545186810, 952802062, 952802061 specifications

Poulan is well-known for producing high-quality outdoor power equipment, and its models 545186810, 952802061, and 952802062 exemplify the brand's commitment to innovation and reliability. These products are designed to make outdoor tasks more manageable, whether for homeowners or professionals.

The Poulan 545186810 is a robust chainsaw that embodies power and efficiency. Its key features include a powerful 18-inch bar and chain, which allows for smooth cutting through various types of wood, from light pruning to heavier tree cutting. The chainsaw is equipped with an automatic oiling system, ensuring that the chain remains lubricated during use, thus extending its life and performance. Additionally, it incorporates a primer bulb for easy starting, allowing users to quickly get to work without the hassle of complicated starting procedures. Ergonomically designed handles offer comfort and grip while working for extended periods.

Next, the Poulan 952802061 is a versatile leaf blower that stands out for its lightweight design and high performance. It features a powerful two-cycle engine that delivers excellent airflow and speed, making leaf and debris cleanup quick and efficient. The blower includes multiple speed settings, allowing users to customize airflow according to the specific needs of the task, whether it’s clearing a small patio or tackling a large yard. A comfortable, padded handle enhances user experience, reducing fatigue during extended use.

Lastly, the Poulan 952802062 is a hedge trimmer that combines precision cutting with user-friendly features. It boasts a dual-action blade design, which significantly reduces vibration while cutting, making it easier to maintain control and accuracy in your cuts. The 24-inch cutting length is ideal for managing both small bushes and large hedges, and its lightweight construction makes it easy to maneuver. This model also incorporates a safety switch to prevent accidental starts, ensuring user safety during operation.

In summary, the Poulan 545186810, 952802061, and 952802062 highlight Poulan's dedication to delivering powerful, efficient, and user-friendly outdoor equipment. Their innovative technologies and characteristics cater to various outdoor tasks, ensuring that both casual users and professionals can maintain their landscapes with ease and confidence. Whether cutting, blowing, or trimming, Poulan provides the tools needed for a job well done.
Top Page Image Contents