Poulan 115358026 Carburetor Adjustments, Idle Speed-T, BAR Maintenance, Back View of Muffler

Page 15

Steel

Backplate

Muffler

Muffler

Bolts

Aluminum

Backplate Muffler

GasketBolt Cover Locknut

1.Loosen and remove the 3 cylinder cover screws. Remove the cylinder cover.

2.Pull off the spark plug boot.

3.Loosen and remove the locknut from the bolt cover. Remove the bolt cover.

4.Loosen and remove the 2 muffler bolts. Remove the muffler, muffler gasket and backplates. Notice the orientation of these parts for reassembling.

5.Locate the 2 outlet cover screws on the muffler. Loosen and remove both screws. Remove the outlet cover and spark arresting screen.

BACK VIEW OF MUFFLER

Outlet Cover

Muffler

 

Screws

Spark Arresting

Screen

6.Clean the spark arresting screen with a wire brush. Replace screen if any wires are broken or screen is blocked after cleaning.

7.Reinstall spark arresting screen.

8.Reinstall outlet cover and 2 screws. En- sure outlet cover and both screws are reinstalled correctly to prevent damage to the saw (see illustrations). The ex- haust outlets must face the chain brake (bar side) of the saw.

Outlet Cover

Exhaust Outlets

Exhaust Outlets must face chain brake (bar side) of chain saw

9.Inspect the muffler gasket and replace if damaged.

10.Reinstall backplates, muffler gasket and muffler using muffler bolts. Tighten until secure.

11.Reinstall bolt cover and locknut.

12.Reinstall the spark plug boot.

13.Reinstall the cylinder cover and 3 screws. Tighten securely.

CARBURETOR ADJUSTMENTS

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow).

STurn idle speed screw (T) clockwise to in-

crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

15

Image 15
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Maintain ControlReduce the Chance of Kickback Avoid Pinch-KickbackIf your hand slips off the front handlebar Kickback Safety FeaturesChain Brake and CKA Angle Chain saws as set by Ansi B175.1Attaching the BAR & Chain If not AssemblyComputed kickback angle CKA Table Attaching the Bumper Spike If not already attachedChecking the tension Adjusting the tensionInside view Chain Brake Adjustment located on Chain Brake Chain Tension Including units with chain already installedON/STOP ON/STOP Switch Throttle TriggerOperation Know Your SAWChain Tension Throttle LOCK---OUTCHOKE/FAST Idle Lever Chain BrakeImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Important Points Cutting MethodsBraking function control Inertia activating function controlTypes of Cutting Used for Bucking Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsAIR Filter ServiceCleaning the Spark Arresting Screen PruningBack View of Muffler Carburetor AdjustmentsBAR Maintenance Idle Speed-TRight Chain SharpeningTools required To Sharpen ChainStorage Troubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Ligations The U.S. Environmental Limited WarrantyCanada, contact PoulanNANCE, Replacement and Repair of Emission Related Parts Any

115358026, 966558001 specifications

The Poulan 966558001 and 115358026 are two prominent models in the realm of outdoor power equipment, particularly favored for their efficiency and reliability in lawn care and maintenance tasks. Poulan, a brand known for delivering robust and user-friendly tools, has integrated several features and technologies into these models that enhance their performance and usability.

One of the standout features of the Poulan 966558001 is its powerful engine. Designed to deliver consistent performance, the engine provides ample power for cutting through thick grass and tackling difficult terrains. Coupled with a dependable fuel system, this model ensures a prolonged operation without the need for frequent refueling, making it ideal for large lawns and extensive areas.

In contrast, the Poulan 115358026 focuses on lightweight mobility without sacrificing power. Its design is tailored for easy handling, allowing users to navigate tight spaces and maneuver around obstacles effortlessly. This model is particularly suited for homeowners who require a reliable tool for smaller yards or intricate landscaping tasks.

Both models incorporate advanced technologies that enhance their cutting capabilities. An efficient blade system is a hallmark of the Poulan brand, and these models feature sharp, durable blades that provide clean cuts to promote healthier grass growth. Additionally, the adjustable cutting height found in both models allows users to customize their mowing experience according to their lawn's needs, providing versatility for varying grass lengths.

User comfort is another priority reflected in the ergonomic designs of both the 966558001 and 115358026. Equipped with comfortable grips, these mowers reduce strain during extended use, making lawn care less of a chore. Furthermore, the vibration-reducing technology helps to minimize fatigue, ensuring that users can operate the machines for longer periods without discomfort.

Finally, maintenance is made straightforward with both Poulan models. Easy access to key components simplifies cleaning and upkeep, allowing users to maintain their equipment in optimal condition for extended lifespans.

In summary, the Poulan 966558001 and 115358026 exemplify the brand’s commitment to quality and innovation. With their powerful engines, intelligent design, and user-friendly features, these models stand out as reliable choices for effective lawn care, catering to the needs of both casual homeowners and dedicated gardening enthusiasts.