Poulan 966558001 Assembly, Computed kickback angle CKA Table, Attaching the BAR & Chain If not

Page 6

Computed kickback angle (CKA) Table

 

BAR

 

 

CKA without chain brake

MODEL

P/N

 

Length

CHAIN P/N

PP4620AV

530044695

 

20″

952051310

31_

NOTE: If this saw is to be used for commer- cial logging, a chain brake is required and shall not be removed or otherwise disabled to comply with Federal OSHA Regulations for Commercial Logging.

WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

SPECIAL NOTICE: Your saw is equipped with a temperature limiting muffler and spark

arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines to be equipped with a spark arresting screen. If you operate a chain saw in a state or locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the SERVICE section for maintenance of the spark arresting screen.

Failure to follow all Safety Rules and Precau- tions can result in serious injury. If situations occur which are not covered in this manual, use care and good judgement. If you need assistance, contact your authorized service dealer or call 1-800--554--6723.

STANDARDS: This saw is listed by Under- writer’s Laboratories, Inc., in accordance with: ANSI B175.1-2000American National Standards for Gasoline--Powered Chain Saws -- Safety Requirements

CSA Z62.1-1995 Chain Saws -- Occupa- tional Health and Safety

CSA Z62.3-1996Chain Saw Kickback Oc- cupational Health and Safety

ASSEMBLY

Protective gloves (not provided) should be worn during assembly.

ATTACHING THE BUMPER SPIKE (If not already attached)

The bumper spike may be used as a pivot when making a cut.

1.Loosen and remove the chain brake nuts and the chain brake from the saw.

2.Attach the bumper spike with the two screws as illustrated.

ATTACHING THE BAR & CHAIN (If not

already attached)

WARNING: If received assembled, repeat all steps to ensure your saw is prop- erly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving!

NOTE: CHAIN BRAKE MUST BE DIS- ENGAGED BEFORE IT CAN BE RE- MOVED OR INSTALLED ON THE CHAIN SAW. TO DISENGAGE CHAIN BRAKE, PULL THE FRONT HAND GUARD BACK TOWARD THE REAR OF THE CHAIN BRAKE AS FAR AS POSSIBLE (SEE ILLUSTRATION).

DISENGAGED

Front Hand Guard

ENGAGED

Chain Brake

1.Loosen and remove the chain brake nuts and the chain brake from the saw.

2.Remove the plastic shipping spacer (if present).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Manual de Instrucciones Manuel d’Instructions Starting Reminder Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Maintain ControlReduce the Chance of Kickback Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAttaching the Bumper Spike If not already attached AssemblyComputed kickback angle CKA Table Attaching the BAR & Chain If notChain Tension Including units with chain already installed Adjusting the tensionInside view Chain Brake Adjustment located on Chain Brake Checking the tensionKnow Your SAW ON/STOP Switch Throttle TriggerOperation ON/STOPChain Brake Throttle LOCK---OUTCHOKE/FAST Idle Lever Chain TensionImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function control Cutting MethodsBraking function control Important PointsCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Types of Cutting Used for BuckingLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingPruning ServiceCleaning the Spark Arresting Screen AIR FilterIdle Speed-T Carburetor AdjustmentsBAR Maintenance Back View of MufflerTo Sharpen Chain Chain SharpeningTools required RightStorage Troubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Poulan Limited WarrantyCanada, contact Ligations The U.S. EnvironmentalNANCE, Replacement and Repair of Emission Related Parts Any

115358026, 966558001 specifications

The Poulan 966558001 and 115358026 are two prominent models in the realm of outdoor power equipment, particularly favored for their efficiency and reliability in lawn care and maintenance tasks. Poulan, a brand known for delivering robust and user-friendly tools, has integrated several features and technologies into these models that enhance their performance and usability.

One of the standout features of the Poulan 966558001 is its powerful engine. Designed to deliver consistent performance, the engine provides ample power for cutting through thick grass and tackling difficult terrains. Coupled with a dependable fuel system, this model ensures a prolonged operation without the need for frequent refueling, making it ideal for large lawns and extensive areas.

In contrast, the Poulan 115358026 focuses on lightweight mobility without sacrificing power. Its design is tailored for easy handling, allowing users to navigate tight spaces and maneuver around obstacles effortlessly. This model is particularly suited for homeowners who require a reliable tool for smaller yards or intricate landscaping tasks.

Both models incorporate advanced technologies that enhance their cutting capabilities. An efficient blade system is a hallmark of the Poulan brand, and these models feature sharp, durable blades that provide clean cuts to promote healthier grass growth. Additionally, the adjustable cutting height found in both models allows users to customize their mowing experience according to their lawn's needs, providing versatility for varying grass lengths.

User comfort is another priority reflected in the ergonomic designs of both the 966558001 and 115358026. Equipped with comfortable grips, these mowers reduce strain during extended use, making lawn care less of a chore. Furthermore, the vibration-reducing technology helps to minimize fatigue, ensuring that users can operate the machines for longer periods without discomfort.

Finally, maintenance is made straightforward with both Poulan models. Easy access to key components simplifies cleaning and upkeep, allowing users to maintain their equipment in optimal condition for extended lifespans.

In summary, the Poulan 966558001 and 115358026 exemplify the brand’s commitment to quality and innovation. With their powerful engines, intelligent design, and user-friendly features, these models stand out as reliable choices for effective lawn care, catering to the needs of both casual homeowners and dedicated gardening enthusiasts.
Top Page Image Contents