Poulan 115358026 Throttle LOCK---OUT, CHOKE/FAST Idle Lever, Chain Brake, Chain Tension

Page 9

THROTTLE LOCK---OUT

The THROTTLE LOCK--OUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from acci- dentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle speed are set by pull- ing the CHOKE/FAST IDLE LEVER out fully for cold starting or after refueling. The choke provides additional fuel to the engine during cold starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of

kickback. The chain brake activates manu- ally if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during first 15 minutes of operation. You should check your chain tension frequently. See CHAIN TENSION in the ASSEMBLY section.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury to the operator and/or damage the chain mak- ing it unusable.

BEFORE STARTING ENGINE

WARNING: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand synthetic oil. Pour the entire contents of this container into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major engine performance and durability problems.

WARNING: Alternative fuels (not gasoline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of al- ternative fuels will cause problems such as: im- proper clutch engagements, overheating, va- por lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubrica- tion. Lubrication is provided by the automatic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/or discolor- ation of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. Poulan oil resists high temperature thinning. If Poulan bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 If your hand slips off the front handlebarComputed kickback angle CKA Table AssemblyAttaching the Bumper Spike If not already attached Attaching the BAR & Chain If notInside view Chain Brake Adjustment located on Chain Brake Adjusting the tensionChain Tension Including units with chain already installed Checking the tensionOperation ON/STOP Switch Throttle TriggerKnow Your SAW ON/STOPCHOKE/FAST Idle Lever Throttle LOCK---OUTChain Brake Chain TensionImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Cutting MethodsInertia activating function control Important PointsNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Types of Cutting Used for BuckingBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingCleaning the Spark Arresting Screen ServicePruning AIR FilterBAR Maintenance Carburetor AdjustmentsIdle Speed-T Back View of MufflerTools required Chain SharpeningTo Sharpen Chain RightStorage Troubleshooting Table Cause Remedy Load Adjustment EngineEmpty fuel tank and refill with Canada, contact Limited WarrantyPoulan Ligations The U.S. EnvironmentalNANCE, Replacement and Repair of Emission Related Parts Any

115358026, 966558001 specifications

The Poulan 966558001 and 115358026 are two prominent models in the realm of outdoor power equipment, particularly favored for their efficiency and reliability in lawn care and maintenance tasks. Poulan, a brand known for delivering robust and user-friendly tools, has integrated several features and technologies into these models that enhance their performance and usability.

One of the standout features of the Poulan 966558001 is its powerful engine. Designed to deliver consistent performance, the engine provides ample power for cutting through thick grass and tackling difficult terrains. Coupled with a dependable fuel system, this model ensures a prolonged operation without the need for frequent refueling, making it ideal for large lawns and extensive areas.

In contrast, the Poulan 115358026 focuses on lightweight mobility without sacrificing power. Its design is tailored for easy handling, allowing users to navigate tight spaces and maneuver around obstacles effortlessly. This model is particularly suited for homeowners who require a reliable tool for smaller yards or intricate landscaping tasks.

Both models incorporate advanced technologies that enhance their cutting capabilities. An efficient blade system is a hallmark of the Poulan brand, and these models feature sharp, durable blades that provide clean cuts to promote healthier grass growth. Additionally, the adjustable cutting height found in both models allows users to customize their mowing experience according to their lawn's needs, providing versatility for varying grass lengths.

User comfort is another priority reflected in the ergonomic designs of both the 966558001 and 115358026. Equipped with comfortable grips, these mowers reduce strain during extended use, making lawn care less of a chore. Furthermore, the vibration-reducing technology helps to minimize fatigue, ensuring that users can operate the machines for longer periods without discomfort.

Finally, maintenance is made straightforward with both Poulan models. Easy access to key components simplifies cleaning and upkeep, allowing users to maintain their equipment in optimal condition for extended lifespans.

In summary, the Poulan 966558001 and 115358026 exemplify the brand’s commitment to quality and innovation. With their powerful engines, intelligent design, and user-friendly features, these models stand out as reliable choices for effective lawn care, catering to the needs of both casual homeowners and dedicated gardening enthusiasts.
Top Page Image Contents