Poulan 545186805 instruction manual Chain Tension, Checking the tension, Adjusting the tension

Page 7

Adjusting

Screw

Tensioning Rack

4.Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket.

Bar bolts

Guide bar

5.Carefully remove the chain from the pack- age. Hold chain with the drive links as shown.

Tip of

Bar

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

6.Place chain over and behind the clutch retainer, fitting the drive links in the clutch drum sprocket.

7.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

8.Fit chain drive links into bar groove.

9.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

10.Hold guide bar against the saw frame and install clutch cover.

11.Install bar nuts and finger tighten only. Once the chain is tensioned, you will need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the bar nuts are finger tight only. Attempting to tension the chain when the bar nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

 

Bar

 

Chain Adjustment

Bar Nuts

Tool

(Bar Tool)

 

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time be- fore you start the chain saw.

An adjusting screw (located on the guide bar) is used to adjust the tension of the chain (see illustration).

1.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Guide bar

Adjusting

Screw

2.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

3.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw clockwise until sag does not exist.

4.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

Bar Nuts

5.Use the screwdriver end of the bar tool to move chain around guide bar.

6.If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw. Retighten bar nuts.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Using the chain sawAlways use two hands when operating the chain saw Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackChain Brake and CKA Angle Kickback Safety FeaturesIf your hand slips off the front handlebar Attaching the BAR & Chain If not AssemblyChain Tension Adjusting the tensionChecking the tension Operation Fuel Requirements Before Starting Engine Fueling EngineBAR and Chain Lubrication Kickback occurs Important Points to RememberStarting a Warm Engine Difficult Starting or starting a flooded engineTree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsTypes of Cutting Used for Bucking Notch CUT and Felling the TreeCutting a Fallen Tree Important PointsLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenReplace Fuel Filter Chain AdjustmentReplace Spark Plug To Sharpen ChainSeasonal Storage Carburetor AdjustmentStorage Cooling SystemEngine Load Adjustment EngineOther Ligations The U.S. Environmental Poulan PROIntermediate 125 hours Extended 300 hours

545186805 specifications

The Poulan 545186805 is an impressive chainsaw designed to meet the demands of both the seasoned professional and the enthusiastic DIYer. This chainsaw combines robust performance with user-friendly features, making it a popular choice among users looking for reliability and efficiency.

One of the key characteristics of the Poulan 545186805 is its powerful engine. Equipped with a 50cc two-stroke engine, it delivers impressive cutting power that allows users to tackle large logs and tough tree trunks with ease. This engine is designed for optimal performance, offering a balance of power and fuel efficiency, ensuring that users can work longer without frequently stopping to refuel.

In addition to its potent engine, the Poulan 545186805 features a 20-inch guide bar, allowing for deeper cuts and the ability to handle larger wood types. This extended reach is particularly beneficial for users who need to fell trees or cut through thicker branches, adding versatility to its applications.

Safety is an important factor for chainsaw users, and the Poulan 545186805 incorporates several safety features designed to protect users. It has an automatic chain oiler which achieves continuous lubrication, reducing wear on the chain and the bar, thereby enhancing longevity. Additionally, it comes equipped with a chain brake that reduces the risk of kickback, ensuring safer operation.

The design of the Poulan 545186805 emphasizes comfort and ease of use. It features an ergonomic handle that provides a secure grip, reducing fatigue during extended use. The lightweight construction further enhances maneuverability, making it easier to handle for extended periods, which is especially important for those undertaking larger projects.

Moreover, the Poulan 545186805 integrates advanced technology to ensure a smoother operation. The Easy Start feature allows users to start the engine with minimal effort, preventing frustration and providing a user-friendly experience, particularly for those who may not be accustomed to handling chainsaws.

In summary, the Poulan 545186805 is a versatile and powerful chainsaw that stands out with its combination of performance, safety, and user-friendly features. Whether for professional use or home projects, this chainsaw can effectively meet the needs of a variety of users, making it a solid choice for anyone in need of a reliable cutting tool.
Top Page Image Contents