Poulan 952802151 Braking function control Caution The chain brake must be, Operating Tips

Page 11

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

SCheck chain tension before first use, after 1 minute of operation, and each time be-

fore you start the chain saw. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary. If the chain jumps off the guide bar, inspect the chain for damaged drive links before reinstalling. Burrs on drive links, which prevent them from entering the groove of the guide bar,

can be removed with a flat file.

SKeep the chain out of dirt and sand. Even a small amount of dirt will dull a chain, increase

the possibility of kickback, and require chain sharpening or replacement.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for lon-

ger than 30 seconds at full throttle.

STo avoid losing control when cut is com- plete, do not put pressure on saw at end of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified im- mediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You need a clear area all around the tree so you can have secure footing.

SThe chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause

the tree to fall in a particular direction. Natural conditions that can cause a tree to fall in a particular direction include:

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Attaching the BAR & Chain If not AssemblyChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation Chain Brake Throttle LOCK-OUTCHOKE/FAST Idle Lever Primer BulbRight Foot Through Rear Handle Important Points to RememberStarting a Warm Engine Difficult Starting or starting a flooded engineTree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsImportant Points Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsCheck for Damaged or Worn Parts ServicePruning General RecommendationsCheck Guide BAR Inspect and Clean Unit and DecalsClean AIR Filter Check Chain SharpnessReplace Fuel Filter Cleaning the Spark ARREST- ING ScreenChain Adjustment Replace Spark PlugRight Carburetor AdjustmentIdle Speed-T Cooling SystemEngine StorageSeasonal Storage Fuel SystemEmpty fuel tank and refill with Load Adjustment EngineLigations The U.S. Environmental Poulan

952802151, 545186809 specifications

The Poulan 545186809, 952802151 is a robust and efficient chainsaw designed for both professional and residential use. This model seamlessly blends innovation with power, making it a reliable tool for a variety of cutting tasks, from light pruning to heavy-duty tree felling.

One of the standout features of the Poulan 545186809 is its powerful engine. Equipped with a 45cc engine, it delivers sufficient power to handle tough cutting jobs while maintaining optimal fuel efficiency. The engine operates smoothly, reducing vibrations and minimizing user fatigue during prolonged use. This makes it an ideal choice for those who require a dependable chainsaw for extended periods.

The design of the Poulan 545186809 also incorporates advanced technologies aimed at enhancing user experience. An automatic oiler system ensures that the chain remains lubricated at all times, reducing friction and wear. This feature not only prolongs the life of the chain but also promotes smoother cuts. The tool-less chain tensioning mechanism allows users to adjust the chain tension quickly and conveniently without the need for additional tools— an essential feature for on-the-go adjustments.

Safety is a primary consideration with the Poulan 545186809. The chainsaw is equipped with an inertia-activated chain brake, which stops the chain immediately in the event of kickback, safeguarding the operator from injuries. Additionally, the model features a sturdy front guard that offers extra protection while maintaining visibility of the cutting area.

Another notable characteristic is its lightweight and ergonomic design. Weighing in at just over 10 pounds, it is manageable for most users, and the cushioned grip provides comfort, reducing strain on the hands. The compact build also allows for easy maneuverability, making it perfect for tight spaces.

In terms of maintenance, the Poulan 545186809 is user-friendly. The air filter is easily accessible for cleaning or replacement, thus ensuring the engine operates at peak performance.

Overall, the Poulan 545186809, 952802151 is a powerful, versatile, and safe chainsaw that can tackle various cutting tasks with ease. Its combination of innovative features, safety mechanisms, and user comfort makes it an excellent choice for anyone looking to invest in a high-quality chainsaw. Whether for professional landscaping or casual home use, this model stands out as a reliable tool in the world of outdoor equipment.
Top Page Image Contents