Poulan 545047541 instruction manual Cutting Methods, Starting a Warm Engine, Important Points

Page 10

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/ fast idle lever OFF HALF FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Slowly press the primer bulb 6 times.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14 inches (35 cm) above a stump or other wooden surface. Re- lease your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions English FrançaisStarting Reminder Identification of SymbolsSafety Rules Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackDo not cut more than one log at a time Maintain ControlReduce the Chance of Kickback Elbow locked Clear The Working AreaChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Guide bar up and back toward the operatorInside view Chain Brake Adjustment located on Chain Brake AssemblyComputed kickback angle CKA Table Adjusting the tension Checking the tensionThrottle Trigger ON/STOP SwitchKnow Your SAW Throttle LockoutBAR and Chain Lubrication StartingFueling Engine Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Notch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Carefully plan your sawing operation in ad- vanceTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points ServicePruning LimbingCarburetor Adjustment Cleaning the air filterCleaning the Spark ARREST- ING Screen Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Load Adjustment Engine Limited WarrantyEmpty fuel tank and refill with Tions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCIntermediate 125 hours Extended 300 hours

545047541 specifications

The Poulan 545047541 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Boasting a range of impressive features and innovative technologies, this chainsaw is engineered to deliver optimal performance while ensuring user comfort and safety.

One of the standout features of the Poulan 545047541 is its robust 50cc engine. This powerful engine provides ample horsepower, enabling it to tackle tough cutting jobs, such as felling trees, cutting firewood, and trimming larger branches with ease. The chainsaw is designed to handle demanding tasks while maintaining efficient fuel consumption, making it an economical choice for users who require a reliable chainsaw for regular usage.

The design of the Poulan 545047541 incorporates an automatic oiling system that ensures the chain and bar are consistently lubricated during operation. This feature not only enhances the lifespan of the chainsaw but also minimizes chain friction for smoother, more efficient cutting. The adjustable oil pump allows users to control the amount of oil dispensed based on the type of wood and the cutting conditions, further optimizing performance.

Safety is a top priority with the Poulan 545047541. It includes a chain brake mechanism that stops the chain almost instantly in case of kickback, providing necessary protection for the user. Additionally, features such as a rear handle with an anti-vibration system help to reduce fatigue during extended use, making it more comfortable to operate.

The chainsaw also features an ergonomically designed handle that ensures a secure grip, allowing users to maneuver the tool effectively. A visible fuel and oil indicator simplifies monitoring levels, preventing unexpected interruptions during work.

Moreover, the Poulan 545047541 is equipped with an easy-access air filter and spark plug, making maintenance straightforward. When it comes to storage, its lightweight build adds to its portability, allowing for easy transportation.

In summary, the Poulan 545047541 is an exceptional chainsaw that combines power, efficiency, and safety features to meet the demands of both professional and casual users. With its user-friendly design and advanced technologies, it stands as a reliable tool for anyone looking to manage cutting tasks seamlessly.
Top Page Image Contents