Poulan 545047541 instruction manual Starting, Fueling Engine, BAR and Chain Lubrication

Page 9

FUELING & LUBRICATION

WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of Poulan/Weed Eater brand synthetic oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine PoulanR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. PoulanR oil resists high temperature thinning. If PoulanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15 --- 18 inches (38 --- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel):

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull out choke/fast idle to the full extent (to the FULL CHOKE position).

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents English Français Manual de Instrucciones Manuel d’InstructionsSafety Rules Identification of SymbolsStarting Reminder Plan AheadMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlDo not cut more than one log at a time Elbow locked Clear The Working AreaChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Guide bar up and back toward the operatorAssembly Inside view Chain Brake Adjustment located on Chain BrakeComputed kickback angle CKA Table Checking the tension Adjusting the tensionKnow Your SAW ON/STOP SwitchThrottle Trigger Throttle LockoutFueling Engine StartingBAR and Chain Lubrication Important Points to RememberCutting Methods Starting a Warm EngineImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Carefully plan your sawing operation in ad- vanceCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportPruning ServiceLimbing and Pruning Important Points LimbingCleaning the Spark ARREST- ING Screen Cleaning the air filterCarburetor Adjustment Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Tions The U.S. Environmental ProtectionIntermediate 125 hours Extended 300 hours

545047541 specifications

The Poulan 545047541 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Boasting a range of impressive features and innovative technologies, this chainsaw is engineered to deliver optimal performance while ensuring user comfort and safety.

One of the standout features of the Poulan 545047541 is its robust 50cc engine. This powerful engine provides ample horsepower, enabling it to tackle tough cutting jobs, such as felling trees, cutting firewood, and trimming larger branches with ease. The chainsaw is designed to handle demanding tasks while maintaining efficient fuel consumption, making it an economical choice for users who require a reliable chainsaw for regular usage.

The design of the Poulan 545047541 incorporates an automatic oiling system that ensures the chain and bar are consistently lubricated during operation. This feature not only enhances the lifespan of the chainsaw but also minimizes chain friction for smoother, more efficient cutting. The adjustable oil pump allows users to control the amount of oil dispensed based on the type of wood and the cutting conditions, further optimizing performance.

Safety is a top priority with the Poulan 545047541. It includes a chain brake mechanism that stops the chain almost instantly in case of kickback, providing necessary protection for the user. Additionally, features such as a rear handle with an anti-vibration system help to reduce fatigue during extended use, making it more comfortable to operate.

The chainsaw also features an ergonomically designed handle that ensures a secure grip, allowing users to maneuver the tool effectively. A visible fuel and oil indicator simplifies monitoring levels, preventing unexpected interruptions during work.

Moreover, the Poulan 545047541 is equipped with an easy-access air filter and spark plug, making maintenance straightforward. When it comes to storage, its lightweight build adds to its portability, allowing for easy transportation.

In summary, the Poulan 545047541 is an exceptional chainsaw that combines power, efficiency, and safety features to meet the demands of both professional and casual users. With its user-friendly design and advanced technologies, it stands as a reliable tool for anyone looking to manage cutting tasks seamlessly.
Top Page Image Contents