Poulan 545047541 Cleaning the air filter, Inspect Muffler and Spark Arresting Screen

Page 14

Cleaning the air filter:

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean after 10 tanks of fuel or 5 hours of operation, which- ever comes first. Clean more frequently in dusty conditions. A used aire filter can never be completely cleaned. It is advisable to re- place your air filter with a new one after every 50 hours of operation, or annually, whichever comes first.

1.Loosen 3 screws on cylinder cover.

2.Remove cylinder cover.

3.Remove air filter.

4.Clean the air filter using hot soapy water. Rinse with clean cool water. Air dry com- pletely before reinstalling.

5.Lightly oil air filter before installing to im- prove the efficiency of air filter. Use 2--cycle engine oil or motor oil (SAE 30). Squeeze excess oil from filter.

6.Reinstall air filter.

7.Reinstall cylinder cover and 3 screws. TIghten securely.

Cylinder

4.Locate the 2 outlet cover screws on the muffler. Loosen and remove both screws.

5.Remove the outlet cover.

Outlet Cover

BACK VIEW OF

 

MUFFLER

 

Muffler

Screws

 

Spark Arresting

 

Screen

 

6.Remove spark arresting screen.

7.Clean the spark arresting screen with a wire brush. Replace screen if any wires are broken or screen is blocked after cleaning.

8.Reinstall spark arresting screen.

9.Reinstall outlet cover and 2 screws. En- sure outlet cover and both screws are re- installed correctly (see illustrations) to prevent damage to the saw. The ex- haust outlet must face the chain brake (bar side) of the saw.

Air Filter

Cover

 

 

Screws

 

Cylinder

 

Cover

Exhaust

Outlet

Outlet Cover

INSPECT MUFFLER AND SPARK ARRESTING SCREEN

As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire hazard or affecting engine performance.

Replace the spark arresting screen if breaks occur.

CLEANING THE SPARK ARREST- ING SCREEN

Cleaning is required every 25 hours of op- eration or annually, whichever comes first.

Outlet

Guide

Muffler

Muffler

BackplateBolts

Muffler

Gasket

Bolt Cover Locknut

1.Loosen and remove the locknut from the bolt cover.

2.Remove the bolt cover.

3.Loosen and remove the 2 muffler bolts. Remove the muffler, muffler gasket, out- let guide and backplate. Notice the ori- entation of these parts for reassembling.

Exhaust Outlet must face chain brake (bar side) of chain saw

10.Inspect the muffler gasket and replace if damaged.

11.Reinstall backplate, outlet guide, muffler gasket, and muffler using muffler bolts. Tighten until secure.

12.Reinstall bolt cover and locknut. Tighten securely.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock-

wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Manual de Instrucciones Manuel d’Instructions English FrançaisStarting Reminder Identification of SymbolsSafety Rules Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackDo not cut more than one log at a time Maintain ControlReduce the Chance of Kickback Elbow locked Clear The Working AreaChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Guide bar up and back toward the operatorComputed kickback angle CKA Table AssemblyInside view Chain Brake Adjustment located on Chain Brake Adjusting the tension Checking the tensionThrottle Trigger ON/STOP SwitchKnow Your SAW Throttle LockoutBAR and Chain Lubrication StartingFueling Engine Important Points to RememberImportant Points Cutting MethodsStarting a Warm Engine Notch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Carefully plan your sawing operation in ad- vanceTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points ServicePruning LimbingCarburetor Adjustment Cleaning the air filterCleaning the Spark ARREST- ING Screen Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Empty fuel tank and refill with Limited WarrantyLoad Adjustment Engine Tions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCIntermediate 125 hours Extended 300 hours

545047541 specifications

The Poulan 545047541 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Boasting a range of impressive features and innovative technologies, this chainsaw is engineered to deliver optimal performance while ensuring user comfort and safety.

One of the standout features of the Poulan 545047541 is its robust 50cc engine. This powerful engine provides ample horsepower, enabling it to tackle tough cutting jobs, such as felling trees, cutting firewood, and trimming larger branches with ease. The chainsaw is designed to handle demanding tasks while maintaining efficient fuel consumption, making it an economical choice for users who require a reliable chainsaw for regular usage.

The design of the Poulan 545047541 incorporates an automatic oiling system that ensures the chain and bar are consistently lubricated during operation. This feature not only enhances the lifespan of the chainsaw but also minimizes chain friction for smoother, more efficient cutting. The adjustable oil pump allows users to control the amount of oil dispensed based on the type of wood and the cutting conditions, further optimizing performance.

Safety is a top priority with the Poulan 545047541. It includes a chain brake mechanism that stops the chain almost instantly in case of kickback, providing necessary protection for the user. Additionally, features such as a rear handle with an anti-vibration system help to reduce fatigue during extended use, making it more comfortable to operate.

The chainsaw also features an ergonomically designed handle that ensures a secure grip, allowing users to maneuver the tool effectively. A visible fuel and oil indicator simplifies monitoring levels, preventing unexpected interruptions during work.

Moreover, the Poulan 545047541 is equipped with an easy-access air filter and spark plug, making maintenance straightforward. When it comes to storage, its lightweight build adds to its portability, allowing for easy transportation.

In summary, the Poulan 545047541 is an exceptional chainsaw that combines power, efficiency, and safety features to meet the demands of both professional and casual users. With its user-friendly design and advanced technologies, it stands as a reliable tool for anyone looking to manage cutting tasks seamlessly.
Top Page Image Contents