Poulan 545123582 instruction manual Need ASSISTANCE?

Page 15

If you require further assistance or are unsure about performing this procedure, contact your

authorized

service

dealer

or

call

1--800--554--6723.

 

 

 

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi- tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0.6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

 

Plug

 

STORAGE

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

NEED ASSISTANCE?

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your dealer or place of purchase.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 545123582 8/25/06 English Español FrançaisPlan Ahead Identification of SymbolsSafety Rules Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionDo not cut more than one log at a time Kickback Safety FeaturesReduce the Chance of Kickback Maintain ControlIf your hand slips off the front handlebar Chain Brake and CKA AngleInside view Chain Brake Adjustment located on Chain Brake AssemblyAdjusting the tension Chain TensionChecking the tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationInertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beFelling Large Trees Cutting MethodsImportant Points Tree Felling TechniquesBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment AIR FilterNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Ligations The U. S. Environmental Parts List Carburetor, Ignition SystemIntermediate 125 hours Extended 300 hours

545123582 specifications

The Poulan 545123582 chainsaw stands out as a reliable and powerful tool designed for both homeowners and professionals alike. Engineered with a strong emphasis on performance, this model is equipped with a host of features and technologies that enhance its usability and effectiveness in a variety of cutting applications.

One of the key characteristics of the Poulan 545123582 is its robust engine. This chainsaw features a high-performance gasoline engine that provides ample power for cutting through tough materials. The engine's efficient design ensures that it runs smoothly, allowing the user to tackle large logs and branches with ease. The combination of power and efficiency enables operators to complete their tasks quickly without excessive fatigue.

Another standout feature of this chainsaw is its lightweight and ergonomic design. Weighing less than many comparable models, the Poulan 545123582 allows users to maneuver easily without sacrificing cutting ability. The chainsaw is thoughtfully equipped with anti-vibration technology, which significantly reduces hand fatigue during extended use. This makes it an excellent choice for both amateur and professional users who require a tool that can be operated comfortably for long periods.

The Poulan 545123582 also integrates an adjustable chain tensioning system. This feature allows users to easily modify the chain’s tension without the need for additional tools. Proper chain tension is crucial for optimal cutting performance, and this tool ensures that maintaining that tension is hassle-free. Additionally, the chainsaw is designed with a quick-release air filter, making the maintenance process simpler and more efficient. This feature is vital for ensuring the longevity of the engine and overall performance, as it helps keep debris out and promotes better air flow.

Safety is paramount in the design of the Poulan 545123582. It comes equipped with an automatic oiler that delivers the right amount of lubrication to the chain, reducing wear and enhancing cutting efficiency. Also, the chainsaw features a chain brake that activates in case of kickback, providing an added layer of safety for users.

With a well-rounded combination of power, comfort, and user-friendly features, the Poulan 545123582 chainsaw is an excellent investment for anyone looking to accomplish their cutting tasks effectively and safely. Whether trimming trees or cutting firewood, this model is engineered to meet a wide range of needs while ensuring ease of use and operational longevity.
Top Page Image Contents