Poulan 545123582 instruction manual Starting, Fueling Engine, BAR and Chain Lubrication

Page 9

CHAIN TENSION

WARNING: Muffler is very hot dur-

It is normal for a new chain to stretch during the

first 15 minutes of operation. You should check

ing and after use. Do not touch the muffler or

your chain tension frequently. See CHAIN

allow combustible material such as dry

TENSION under the ASSEMBLY section.

grass or fuel to do so.

 

 

 

 

system of an engine while in storage. To

FUELING & LUBRICATION

avoid engine problems, the fuel system

 

should be emptied before storage for 30

 

days or longer. Drain the gas tank, start the

 

FUELING ENGINE

engine and let it run until the fuel lines and

WARNING: Remove fuel cap slow-

carburetor are empty. Use fresh fuel next

season. See STORAGE section for addi-

ly when refueling.

tional information.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air- cooled engine oil designed to be mixed at a ra- tio of 40:1. Poulan/WEED EATER brand syn- thetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. In- cluded with this saw is a 3.2 ounce container of Poulan/WEED EATER brand synthetic oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan bar and chain oil is recom- mended to protect your unit against exces- sive wear from heat and friction. Poulan oil resists high temperature thinning.

If Poulan bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15-- 18(38 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

9

Image 9
Contents 545123582 8/25/06 English Español FrançaisSafety Rules Identification of SymbolsStarting Reminder Plan AheadMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Do not cut more than one log at a timeIf your hand slips off the front handlebar Chain Brake and CKA AngleInside view Chain Brake Adjustment located on Chain Brake AssemblyAdjusting the tension Chain TensionChecking the tension Know Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberDifficult Starting or starting a flooded engine Starting a Warm EngineBraking function control Caution The chain brake must be Inertia activating function controlImportant Points Cutting MethodsTree Felling Techniques Felling Large TreesCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCarburetor Adjustment Cleaning the Spark ARREST- ING ScreenAIR Filter Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Ligations The U. S. Environmental Parts List Carburetor, Ignition SystemIntermediate 125 hours Extended 300 hours

545123582 specifications

The Poulan 545123582 chainsaw stands out as a reliable and powerful tool designed for both homeowners and professionals alike. Engineered with a strong emphasis on performance, this model is equipped with a host of features and technologies that enhance its usability and effectiveness in a variety of cutting applications.

One of the key characteristics of the Poulan 545123582 is its robust engine. This chainsaw features a high-performance gasoline engine that provides ample power for cutting through tough materials. The engine's efficient design ensures that it runs smoothly, allowing the user to tackle large logs and branches with ease. The combination of power and efficiency enables operators to complete their tasks quickly without excessive fatigue.

Another standout feature of this chainsaw is its lightweight and ergonomic design. Weighing less than many comparable models, the Poulan 545123582 allows users to maneuver easily without sacrificing cutting ability. The chainsaw is thoughtfully equipped with anti-vibration technology, which significantly reduces hand fatigue during extended use. This makes it an excellent choice for both amateur and professional users who require a tool that can be operated comfortably for long periods.

The Poulan 545123582 also integrates an adjustable chain tensioning system. This feature allows users to easily modify the chain’s tension without the need for additional tools. Proper chain tension is crucial for optimal cutting performance, and this tool ensures that maintaining that tension is hassle-free. Additionally, the chainsaw is designed with a quick-release air filter, making the maintenance process simpler and more efficient. This feature is vital for ensuring the longevity of the engine and overall performance, as it helps keep debris out and promotes better air flow.

Safety is paramount in the design of the Poulan 545123582. It comes equipped with an automatic oiler that delivers the right amount of lubrication to the chain, reducing wear and enhancing cutting efficiency. Also, the chainsaw features a chain brake that activates in case of kickback, providing an added layer of safety for users.

With a well-rounded combination of power, comfort, and user-friendly features, the Poulan 545123582 chainsaw is an excellent investment for anyone looking to accomplish their cutting tasks effectively and safely. Whether trimming trees or cutting firewood, this model is engineered to meet a wide range of needs while ensuring ease of use and operational longevity.