Poulan 177167 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 21

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key “OFF” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

•Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

BELT TENSION ROD

SUSPENSION ARMS

 

(DISENGAGED

 

POSITION)

 

CHASSIS

BRACKET

RETAINER

SPRING

ANTI-SWAY

BAR

RETAINER

SPRINGS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

FRONT

MOWER ELECTRIC

BRACKET CLUTCH PULLEY

FRONT

PLATE ASSEMBLY

RETAINER

SPRINGS (BOTH SIDES)

FRONT

MOWER

BRACKET

FIG. 19

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents DPR22H48STA Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsWith Parking To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN Adjustment Front Wheel CamberTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor Model Number DPR22H48STA SchematicElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle See Breakdown Steering Assembly KEY Part NO. NO. Description Optional Equipment EngineSeat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

177167 specifications

The Poulan 177167 is an advanced, high-performance chainsaw designed for both professional loggers and dedicated home users. Renowned for its robust construction and reliability, this model is engineered to handle a variety of cutting tasks, from felling trees to pruning branches and cutting firewood.

One of the standout features of the Poulan 177167 is its powerful 42cc engine, which provides ample strength for heavy-duty cutting applications. The engine is designed with a high horsepower-to-weight ratio, allowing users to operate the chainsaw efficiently without feeling overly fatigued. The easy start technology ensures that you can get going quickly without the frustration often associated with starting small engines.

This chainsaw incorporates a 16-inch bar, balanced for optimum maneuverability, making it suitable for various types of cutting jobs. The low-kickback chain design enhances user safety while providing smoother cutting action. The chain is also easy to replace and maintain, thanks to the tool-less chain tensioning feature. This allows for simple adjustments without the need for additional tools, making it convenient for users in the field.

Durability is a key characteristic of the Poulan 177167. The body of the chainsaw is constructed from high-quality materials designed to withstand the rigors of demanding tasks. Additionally, it features an automatic oiling system which continuously lubricates the chain, reducing wear and extending the life of the bar and chain assembly.

User comfort is prioritized in the design of the Poulan 177167, which includes a comfortable, ergonomically designed handle that reduces vibration and enhances grip. This minimizes hand fatigue during prolonged use, allowing users to stay focused on their cutting tasks.

Safety mechanisms such as the chain brake and throttle interlock are incorporated to protect users from accidents. The chain brake activates automatically during a kickback, stopping the chain instantly and providing peace of mind while operating the saw.

In summary, the Poulan 177167 is a feature-rich chainsaw designed for both versatility and durability. It combines a powerful engine with user-friendly technologies and safety features, making it an excellent choice for anyone in need of reliable cutting performance, whether for professional logging or home landscaping projects.
Top Page Image Contents