Poulan 177167 owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 27

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Customer Responsibilities section of this manual).

•Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjust- ments section of this manual).

•Lubricate as shown in the Customer Responsibilities section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Customer Responsibilities section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Drain the fuel tank.

•Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Customer Responsibilities section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents DPR22H48STA Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsWith Parking Front Wheel Camber Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor Model Number DPR22H48STA SchematicElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle See Breakdown Steering Assembly KEY Part NO. NO. Description Optional Equipment EngineSeat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

177167 specifications

The Poulan 177167 is an advanced, high-performance chainsaw designed for both professional loggers and dedicated home users. Renowned for its robust construction and reliability, this model is engineered to handle a variety of cutting tasks, from felling trees to pruning branches and cutting firewood.

One of the standout features of the Poulan 177167 is its powerful 42cc engine, which provides ample strength for heavy-duty cutting applications. The engine is designed with a high horsepower-to-weight ratio, allowing users to operate the chainsaw efficiently without feeling overly fatigued. The easy start technology ensures that you can get going quickly without the frustration often associated with starting small engines.

This chainsaw incorporates a 16-inch bar, balanced for optimum maneuverability, making it suitable for various types of cutting jobs. The low-kickback chain design enhances user safety while providing smoother cutting action. The chain is also easy to replace and maintain, thanks to the tool-less chain tensioning feature. This allows for simple adjustments without the need for additional tools, making it convenient for users in the field.

Durability is a key characteristic of the Poulan 177167. The body of the chainsaw is constructed from high-quality materials designed to withstand the rigors of demanding tasks. Additionally, it features an automatic oiling system which continuously lubricates the chain, reducing wear and extending the life of the bar and chain assembly.

User comfort is prioritized in the design of the Poulan 177167, which includes a comfortable, ergonomically designed handle that reduces vibration and enhances grip. This minimizes hand fatigue during prolonged use, allowing users to stay focused on their cutting tasks.

Safety mechanisms such as the chain brake and throttle interlock are incorporated to protect users from accidents. The chain brake activates automatically during a kickback, stopping the chain instantly and providing peace of mind while operating the saw.

In summary, the Poulan 177167 is a feature-rich chainsaw designed for both versatility and durability. It combines a powerful engine with user-friendly technologies and safety features, making it an excellent choice for anyone in need of reliable cutting performance, whether for professional logging or home landscaping projects.
Top Page Image Contents