Poulan 530165320-01 instruction manual Cutting Methods, Starting a Warm Engine, Important Points

Page 10

ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/ fast idle lever OFF HALF FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 5 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho-

rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and

after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents English Español Français 16/04Safety Rules Identification of SymbolsPlan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Back toward the operator Chain Brake and CKA AngleFront Hand Guard, designed to reduce 952044370Attaching the BAR & Chain If not AssemblyInside view Chain Brake Adjustment located on Chain Brake Chain Brake NutsChecking the tension Adjusting the tensionChain Tension Throttle Trigger ON/STOP SwitchKnow Your Chain SAW Throttle LOCK-OUTBAR and Chain Lubrication StartingFueling Engine Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Notch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Direction of FallTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing ServiceLimbing and Pruning Important Points PruningAIR Filter Cleaning the air filterCleaning the Spark ARREST- ING Screen Inspect Muffler and Spark Arresting ScreenChain Sharpening Carburetor AdjustmentBAR Maintenance Ignition TimingStorage Need Service PART?Need ASSISTANCE? Need ASSISTANCE?Limited Warranty Tions The U.S. Environmental ProtectionPlacement and Repair of Emission

530165320-01 specifications

The Poulan 530165320-01 is a remarkable addition to the landscaping and outdoor power tool market, renowned for its robust features and advanced technologies designed to meet the needs of homeowners and professionals alike. This versatile model serves as a powerful companion for trimming, edging, and maintaining lawns, ensuring that users achieve a professional finish with ease.

One of the standout features of the Poulan 530165320-01 is its impressive engine performance. Equipped with a reliable two-cycle gas engine, it delivers ample power to handle thick grass and stubborn weeds efficiently. The engine’s robust design ensures longevity while providing smooth and consistent power output. This makes it an ideal choice for tackling a variety of landscaping tasks, from simple yard maintenance to more complex projects.

Another significant aspect of the Poulan 530165320-01 is its ergonomic design. The tool is designed with user comfort in mind, featuring a lightweight frame that minimizes fatigue during extended use. The adjustable handle allows users to customize their grip for improved control and maneuverability, making it easier to navigate tight spaces and uneven terrain. Additionally, the anti-vibration technology incorporated in this model helps reduce hand strain, enabling longer working sessions without discomfort.

The Poulan 530165320-01 also boasts a quick and easy starting mechanism, which is particularly beneficial for users who value efficiency. The innovative Easy Start technology minimizes the effort needed to start the engine, ensuring that even novice users can operate the tool without frustration. The automatic line feed system enhances convenience by providing a continuous supply of trimmer line, reducing downtime for reloading.

Moreover, this model features a durable cutting head that is adaptable for various trimming applications. This versatility is a key selling point, allowing users to switch between different cutting attachments, such as blades and string, depending on the specific requirements of their tasks. The durable construction of the cutting head also means it can withstand the rigors of heavy use, providing reliable performance over time.

In summary, the Poulan 530165320-01 is an exceptional choice for anyone in need of a versatile and powerful outdoor tool. Its blend of cutting-edge technology, ergonomic design, and efficient performance ensures that users can tackle any landscaping challenge with confidence and ease. Whether you’re maintaining your garden or handling larger projects, this model stands out as a trusted partner in outdoor work.
Top Page Image Contents