Poulan 530165320-01 Carburetor Adjustment, BAR Maintenance, Chain Sharpening, Ignition Timing

Page 15

Exhaust

Outlet

Outlet Cover

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Exhaust Outlet must face chain brake (bar side) of chain saw

10.Inspect the muffler gasket and replace if damaged.

11.Reinstall backplate, outlet guide, muffler gasket, and muffler using muffler bolts. Tighten until secure.

12.Reinstall bolt cover and locknut. Tighten securely.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi- tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from saw.

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0.6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

 

Plug

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 16/04 English Español FrançaisIdentification of Symbols Safety RulesPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionKickback Safety Features Reduce the Chance of KickbackMaintain Control 952044370 Chain Brake and CKA AngleFront Hand Guard, designed to reduce Back toward the operatorChain Brake Nuts AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notAdjusting the tension Checking the tensionChain Tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationCutting Methods Starting a Warm EngineImportant Points Direction of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Need Service PART?Need ASSISTANCE? StorageTions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

530165320-01 specifications

The Poulan 530165320-01 is a remarkable addition to the landscaping and outdoor power tool market, renowned for its robust features and advanced technologies designed to meet the needs of homeowners and professionals alike. This versatile model serves as a powerful companion for trimming, edging, and maintaining lawns, ensuring that users achieve a professional finish with ease.

One of the standout features of the Poulan 530165320-01 is its impressive engine performance. Equipped with a reliable two-cycle gas engine, it delivers ample power to handle thick grass and stubborn weeds efficiently. The engine’s robust design ensures longevity while providing smooth and consistent power output. This makes it an ideal choice for tackling a variety of landscaping tasks, from simple yard maintenance to more complex projects.

Another significant aspect of the Poulan 530165320-01 is its ergonomic design. The tool is designed with user comfort in mind, featuring a lightweight frame that minimizes fatigue during extended use. The adjustable handle allows users to customize their grip for improved control and maneuverability, making it easier to navigate tight spaces and uneven terrain. Additionally, the anti-vibration technology incorporated in this model helps reduce hand strain, enabling longer working sessions without discomfort.

The Poulan 530165320-01 also boasts a quick and easy starting mechanism, which is particularly beneficial for users who value efficiency. The innovative Easy Start technology minimizes the effort needed to start the engine, ensuring that even novice users can operate the tool without frustration. The automatic line feed system enhances convenience by providing a continuous supply of trimmer line, reducing downtime for reloading.

Moreover, this model features a durable cutting head that is adaptable for various trimming applications. This versatility is a key selling point, allowing users to switch between different cutting attachments, such as blades and string, depending on the specific requirements of their tasks. The durable construction of the cutting head also means it can withstand the rigors of heavy use, providing reliable performance over time.

In summary, the Poulan 530165320-01 is an exceptional choice for anyone in need of a versatile and powerful outdoor tool. Its blend of cutting-edge technology, ergonomic design, and efficient performance ensures that users can tackle any landscaping challenge with confidence and ease. Whether you’re maintaining your garden or handling larger projects, this model stands out as a trusted partner in outdoor work.
Top Page Image Contents