Poulan 530163637 instruction manual Cutting a Fallen Tree, Types of Cutting Used for Bucking

Page 12

S DO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

SCut shattered wood very carefully; sharp pieces of wood could be flung toward oper-

ator.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while

cutting and never hold the log with your leg or foot.

S Do not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A

SUPPORT

SOvercut through 1/3 of the diameter of the log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR SUPPORT STAND

SRemember your first cut is always on the compression side of the log.

(Refer to the illustrations below for your

first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support

2nd Cut

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

12

1st Cut

1st Cut

2nd Cut

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance KickbackMaintain Control Your left arm straight with the elbow lockedChain Brake and CKA Angle Computed kickback angle CKA TableFront Hand Guard, designed to reduce Attaching the BAR & Chain If not Tip BarAdjusting the tension Chain Tension Including units with chain already installedChecking the tension ON/STOP Switch Know Your SAWThrottle Trigger Throttle LockoutFueling Engine BAR and Chain LubricationImportant Points to Remember Starting a Warm Engine Difficult Starting or starting a flooded engineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Gine can resultBucking Using a LOG or Support Stand Cutting a Fallen TreeTypes of Cutting Used for Bucking Bucking Without a SupportCleaning the air filter PruningLimbing and Pruning Important Points LimbingCleaning the Spark ARREST- ING Screen Carburetor AdjustmentInspect Muffler and Spark Arresting ScreenBAR Maintenance Need Service PART?Chain Sharpening Ignition TimingTroubleshooting Table Cause Remedy Your Warranty Rights and Obliga Tions The U.S. Environmental Protection

530163637 specifications

The Poulan 530163637 is an innovative tool designed for outdoor enthusiasts and professionals alike. Engineered for versatility and efficiency, this unit showcases a range of features that set it apart in the market of power equipment.

One of the standout aspects of the Poulan 530163637 is its powerful engine. It is equipped with a robust 2-cycle engine, which provides ample power to tackle a variety of cutting tasks, from trimming grass to tackling dense brush. The engine’s efficient design not only maximizes cutting performance but also ensures lower fuel consumption, making it an environmentally friendly option for users.

The tool features an easy-to-use, lightweight design that allows for extended periods of use without causing fatigue. Weighing in at a user-friendly level, the Poulan 530163637 ensures that both amateur gardeners and professional landscapers can navigate their work effortlessly. The ergonomic handle enhances comfort and control, reducing the risk of strain during prolonged operation.

Another key characteristic of the Poulan 530163637 is its start technology. The tool employs a reliable starting mechanism that helps users start it on the first pull. This feature is particularly beneficial for those who are less experienced with power equipment, as it minimizes the frustration that often accompanies starting traditional equipment.

The Poulan 530163637 also incorporates advanced cutting technologies, including dual-line feed systems that allow for efficient and precise cutting. This feature ensures that grass and weeds are trimmed quickly and evenly, enhancing the overall aesthetics of lawns and gardens.

The durability of the Poulan 530163637 is another important factor to consider. Constructed from high-quality materials, it is designed to withstand the rigors of outdoor use. The maintenance-friendly design allows for easy access to key components, making routine maintenance tasks like oil changes and air filter replacements straightforward for users.

In summary, the Poulan 530163637 is a powerful, user-friendly outdoor tool designed for efficiency and ease of use. Its combination of a robust engine, lightweight build, advanced cutting technologies, and durable construction makes it an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are a casual gardener or a landscaping professional, the Poulan 530163637 promises to deliver performance and reliability in every application.
Top Page Image Contents