Poulan 530163637 Starting a Warm Engine, Difficult Starting or starting a flooded engine

Page 10

ON/STOP

Switch

Primer

Bulb

ON/STOP SWITCH

ON STOP

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

S When cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/Fast OFF FULL

Idle Lever

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the full extent, then push the lever back in com- pletely (to the OFF position).

3.Slowly press the primer bulb 6 times.

4.Pull the starter rope quickly with your right hand until the engine starts.

5.Squeeze and release throttle trigger, al- lowing engine to idle.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020! (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14! (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials,

etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance Kickback Your left arm straight with the elbow lockedComputed kickback angle CKA Table Chain Brake and CKA AngleFront Hand Guard, designed to reduce Attaching the BAR & Chain If not Tip BarChain Tension Including units with chain already installed Adjusting the tensionChecking the tension Throttle Trigger ON/STOP SwitchKnow Your SAW Throttle LockoutBAR and Chain Lubrication Fueling EngineImportant Points to Remember Braking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Gine can resultTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points Cleaning the air filterPruning LimbingInspect Muffler and Spark Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment Arresting ScreenChain Sharpening BAR MaintenanceNeed Service PART? Ignition TimingTroubleshooting Table Cause Remedy Your Warranty Rights and Obliga Tions The U.S. Environmental Protection

530163637 specifications

The Poulan 530163637 is an innovative tool designed for outdoor enthusiasts and professionals alike. Engineered for versatility and efficiency, this unit showcases a range of features that set it apart in the market of power equipment.

One of the standout aspects of the Poulan 530163637 is its powerful engine. It is equipped with a robust 2-cycle engine, which provides ample power to tackle a variety of cutting tasks, from trimming grass to tackling dense brush. The engine’s efficient design not only maximizes cutting performance but also ensures lower fuel consumption, making it an environmentally friendly option for users.

The tool features an easy-to-use, lightweight design that allows for extended periods of use without causing fatigue. Weighing in at a user-friendly level, the Poulan 530163637 ensures that both amateur gardeners and professional landscapers can navigate their work effortlessly. The ergonomic handle enhances comfort and control, reducing the risk of strain during prolonged operation.

Another key characteristic of the Poulan 530163637 is its start technology. The tool employs a reliable starting mechanism that helps users start it on the first pull. This feature is particularly beneficial for those who are less experienced with power equipment, as it minimizes the frustration that often accompanies starting traditional equipment.

The Poulan 530163637 also incorporates advanced cutting technologies, including dual-line feed systems that allow for efficient and precise cutting. This feature ensures that grass and weeds are trimmed quickly and evenly, enhancing the overall aesthetics of lawns and gardens.

The durability of the Poulan 530163637 is another important factor to consider. Constructed from high-quality materials, it is designed to withstand the rigors of outdoor use. The maintenance-friendly design allows for easy access to key components, making routine maintenance tasks like oil changes and air filter replacements straightforward for users.

In summary, the Poulan 530163637 is a powerful, user-friendly outdoor tool designed for efficiency and ease of use. Its combination of a robust engine, lightweight build, advanced cutting technologies, and durable construction makes it an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are a casual gardener or a landscaping professional, the Poulan 530163637 promises to deliver performance and reliability in every application.
Top Page Image Contents