Poulan 530163637 BAR Maintenance, Chain Sharpening, Ignition Timing, Spark Plug, Need ASSISTANCE?

Page 15

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and

chain brake. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

SBurring of guide bar rails is a normal process

of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and dis- card.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch socket wrench. Spark plug gap should be 0.025 inches.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

 

 

Cylinder

Spark

 

 

 

 

 

 

 

 

Cover

 

 

 

 

 

 

 

 

 

 

Plug Boot

 

 

 

 

 

 

 

 

 

 

 

 

Spark

 

 

 

 

Plug

 

 

 

 

STORAGE

 

 

 

 

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu-

lar attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an

open flame from hot water heaters, electric motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your authorized service dealer.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionYour left arm straight with the elbow locked Kickback Safety FeaturesReduce the Chance Kickback Maintain ControlChain Brake and CKA Angle Computed kickback angle CKA TableFront Hand Guard, designed to reduce Tip Bar Attaching the BAR & Chain If notAdjusting the tension Chain Tension Including units with chain already installedChecking the tension Throttle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerFueling Engine BAR and Chain LubricationImportant Points to Remember Inertia activating function control Starting a Warm EngineDifficult Starting or starting a flooded engine Braking function control Caution The chain brake must beGine can result Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing Cleaning the air filterPruning Limbing and Pruning Important PointsArresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustment Inspect Muffler and SparkIgnition Timing BAR MaintenanceNeed Service PART? Chain SharpeningTroubleshooting Table Cause Remedy Tions The U.S. Environmental Protection Your Warranty Rights and Obliga

530163637 specifications

The Poulan 530163637 is an innovative tool designed for outdoor enthusiasts and professionals alike. Engineered for versatility and efficiency, this unit showcases a range of features that set it apart in the market of power equipment.

One of the standout aspects of the Poulan 530163637 is its powerful engine. It is equipped with a robust 2-cycle engine, which provides ample power to tackle a variety of cutting tasks, from trimming grass to tackling dense brush. The engine’s efficient design not only maximizes cutting performance but also ensures lower fuel consumption, making it an environmentally friendly option for users.

The tool features an easy-to-use, lightweight design that allows for extended periods of use without causing fatigue. Weighing in at a user-friendly level, the Poulan 530163637 ensures that both amateur gardeners and professional landscapers can navigate their work effortlessly. The ergonomic handle enhances comfort and control, reducing the risk of strain during prolonged operation.

Another key characteristic of the Poulan 530163637 is its start technology. The tool employs a reliable starting mechanism that helps users start it on the first pull. This feature is particularly beneficial for those who are less experienced with power equipment, as it minimizes the frustration that often accompanies starting traditional equipment.

The Poulan 530163637 also incorporates advanced cutting technologies, including dual-line feed systems that allow for efficient and precise cutting. This feature ensures that grass and weeds are trimmed quickly and evenly, enhancing the overall aesthetics of lawns and gardens.

The durability of the Poulan 530163637 is another important factor to consider. Constructed from high-quality materials, it is designed to withstand the rigors of outdoor use. The maintenance-friendly design allows for easy access to key components, making routine maintenance tasks like oil changes and air filter replacements straightforward for users.

In summary, the Poulan 530163637 is a powerful, user-friendly outdoor tool designed for efficiency and ease of use. Its combination of a robust engine, lightweight build, advanced cutting technologies, and durable construction makes it an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are a casual gardener or a landscaping professional, the Poulan 530163637 promises to deliver performance and reliability in every application.
Top Page Image Contents