Poulan 530086528 Starting a Warm Engine, Difficult Starting or starting a flooded engine

Page 10

S Push the choke knob in completely (to the

Disengaged

OFF position); pull the starter rope until the

Engaged

engine starts.

CHOKE

(SIDE VIEW)

Choke knob OFF FULL

SAllow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE:

SMove ON/STOP switch to the ON position. S Push the choke knob in completely (to the

OFF position).

S Slowly press primer bulb 6 times.

S Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

S Sharply pull the starter rope with your right hand until the engine starts.

S Squeeze and release throttle trigger to al- low engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 1/32” thick. Repairs on a chain brake should be made by an authorized service dealer. Take your unit to the place of pur- chase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14! (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials,

etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re-

place parts as necessary.

SKeep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the en- tire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or engine can result.

10

Image 10
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance Kickback Avoid Obstructions Clear The Working AreaResent and YOU should not AS Chain Brake and CKA AngleWE do not REP Sume That the Chain Brake willInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Throttle Trigger ON/STOP SwitchKnow Your Chain SAW Throttle LOCK-OUTBAR and Chain Lubrication Fueling EngineImportant Points to Remember Braking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Bar, and engineTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points Cleaning the air filterPruning LimbingBAR Maintenance Cleaning the Spark ARREST- ING ScreenCarburetor Adjustments Inspect Muffler and Spark Arresting ScreenTroubleshooting Table Cause Remedy StorageContact your dealer or place of purchase Need Service PART?Ligations The U. S. Environmental Eater service centers. call 1--800--554--6723MAINTENANCE, RE Weed Eater servicing center. Conse

530086528 specifications

The Poulan 530086528 is a highly regarded tool in the world of outdoor power equipment, particularly known for its reliable performance and efficiency in lawn maintenance tasks. This versatile product is engineered with a host of innovative features and technologies that cater to both professional landscapers and homeowners alike.

One of the standout characteristics of the Poulan 530086528 is its robust engine, designed to provide ample power for a wide array of trimming and cutting applications. This engine is capable of handling various types of vegetation, making it an ideal choice for tackling everything from grassy patches to dense brush. Moreover, it operates efficiently, reducing fuel consumption without compromising on performance. This fuel efficiency not only saves costs in the long run but also minimizes the environmental impact, a feature that is increasingly important to eco-conscious users.

The design of the Poulan 530086528 incorporates user-friendly elements aimed at enhancing the overall experience. The lightweight construction ensures that users can maneuver the device with ease, reducing fatigue during extended use. Additionally, the ergonomic handle is designed to offer a comfortable grip, promoting better control and precision when cutting varied terrains.

Another key aspect of the Poulan 530086528 is its advanced starting system. It is equipped with a simple-to-use pull start mechanism that significantly reduces the effort required to get the engine running. This feature is particularly valuable for novice users who may struggle with traditional starting methods.

Durability is a critical consideration in the design of the Poulan 530086528. The materials used are engineered to withstand the rigors of frequent use, ensuring that the machine can endure tough conditions without deterioration. Furthermore, regular maintenance is made easier thanks to accessible components, allowing users to perform necessary checks and repairs with minimal hassle.

In terms of versatility, the Poulan 530086528 offers interchangeable attachments that can adapt to various tasks, such as edging, trimming, and even blowing debris. This adaptability extends the functionality of the device, making it a valuable addition to any landscaping toolkit.

In summary, the Poulan 530086528 combines power, efficiency, and user-friendliness, making it a leading choice for outdoor maintenance. Its dependable design, ergonomic features, and multi-tasking capabilities firmly position it as an essential tool for anyone looking to maintain a pristine outdoor space.