Poulan 2250, 2450, 2550, 2550 SE, 2555 Cutting Methods, Starting a Warm Engine, Important Points

Page 10

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/ fast idle lever OFF HALF FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Slowly press the primer bulb 6 times.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14 inches (35 cm) above a stump or other wooden surface. Re- lease your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents English Español Français 16/04Safety Rules Identification of SymbolsPlan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance of Kickback Avoid Obstructions Clear The Working AreaChain Brake and CKA Angle Computed kickback angle CKA TableAttaching the BAR & Chain If not AssemblyInside view Chain Brake Adjustment located on Chain Brake Chain Brake NutsChecking the tension Adjusting the tensionChain Tension Including units with chain already installed CuttersThrottle Trigger ON/STOP SwitchKnow Your SAW Throttle LockoutBAR and Chain Lubrication StartingFueling Engine Important Points to RememberStarting a Warm Engine Cutting MethodsImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Types of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points ServicePruning LimbingBAR Maintenance Cleaning the air filterCarburetor Adjustment Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Load Adjustment Engine Limited WarrantyEmpty fuel tank and refill with Ligations The U. S. Environmental Electrolux Home PRODUCTS, INCIntermediate 125 hours Extended 300 hours

2250, 2450, 2550, 2550 SE, 2555 specifications

The Poulan Pro chainsaw series, including the models 2250, 2450, 2550, 2550 SE, and 2555, represents a solid choice for both professionals and hobbyists in need of reliable cutting performance. Each model comes with distinct characteristics while sharing common technological innovations that define their functionality and efficiency.

The Poulan 2250 is designed for durability and ease of use. Weighing in at a manageable size, this chainsaw features a 50cc engine that delivers impressive power for a variety of cutting tasks. One of its standout features is the automatic oiler, which ensures that the chain is always lubricated, reducing wear and enhancing performance over time.

Next in line is the Poulan 2450, which further builds on the strengths of its predecessor. This model boasts a larger cutting capacity, facilitating challenges posed by thicker materials. It incorporates an easy-start system often appreciated by users who want to avoid the frustration of hard starts, making it a great option for regular maintenance tasks around the yard.

The Poulan 2550 exhibits an even greater commitment to power and efficiency. With a robust 45cc engine, this model effectively combines cutting power with manageable weight. It features an air filter system that promotes longer intervals between cleaning, making it easier for users to maintain the chainsaw in pristine working condition.

The Poulan 2550 SE takes the versatility up a notch. This model is equipped with an ergonomic design that reduces operator fatigue, especially during extended use. It also includes a specialized vibration dampening system, ensuring a more comfortable experience while cutting, which is particularly beneficial for professionals who rely on their equipment for hours on end.

Lastly, the Poulan 2555 combines all the best features from its predecessors while integrating advanced technologies to enhance user experience. This model is designed for straightforward maintenance, featuring tool-less access to the air filter and spark plug, making it easy for users to perform routine upkeep. Additionally, the 2555 is built with a powerful engine that delivers high torque, enabling efficient cutting of tougher materials.

Overall, the Poulan Pro chainsaw series embodies a tradition of reliability and innovation, suitable for a range of users, from casual gardeners to professional landscapers. With features like automatic oilers, ergonomic designs, and advanced air filtration systems, these chainsaws are tailored to meet the demands of various cutting applications, ensuring that users can tackle their tasks with confidence and ease.
Top Page Image Contents