Poulan 2250, 2450, 2550, 2550 SE, 2555 Operate Your SAW Safely, Handle Fuel with Caution

Page 3

SCarefully plan your sawing operation in ad- vance. Do not start cutting until you have a clear work area, secure footing, and, if you are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

SDo not operate a chain saw with one hand.

Serious injury to the operator, helpers, by- standers or any combination of these per- sons may result from one-handed opera- tion. A chain saw is intended for two-handed use.

SOperate the chain saw only in a well-venti- lated outdoor area.

SDo not operate saw from a ladder or in a tree.

SMake sure the chain will not make contact with any object while starting the engine. Never try to start the saw when the guide

bar is in a cut.

SDo not put pressure on the saw at the end of the cut. Applying pressure can cause

you to lose control when the cut is com- pleted.

S Stop the engine before setting the saw down.

SDo not operate a chain saw that is dam- aged, improperly adjusted, or not com- pletely and securely assembled. Always replace bar, chain, hand guard, or chain brake immediately if it becomes damaged,

broken or is otherwise removed.

SWith the engine stopped, hand carry the chain saw with the muffler away from your body, and the guide bar and chain to the rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD WORKING ORDER

SHave all chain saw service performed by a qualified service dealer with the exception of the items listed in the maintenance sec- tion of this manual. For example, if improp- er tools are used to remove or hold the fly- wheel when servicing the clutch, structural

damage to the flywheel can occur and cause the flywheel to burst.

SMake certain the saw chain stops moving when the throttle trigger is released. For correction, refer to CARBURETOR AD-

JUSTMENTS.

SNever modify your saw in any way.

SKeep the handles dry, clean, and free of oil

or fuel mixture.

SKeep fuel and oil caps, screws, and fas-

teners securely tightened.

S Use only PoulanR accessories and re- placement parts as recommended.

HANDLE FUEL WITH CAUTION

SDo not smoke while handling fuel or while

operating the saw.

SEliminate all sources of sparks or flame in the areas where fuel is mixed or poured. There should be no smoking, open flames,

or work that could cause sparks. Allow en- gine to cool before refueling.

SMix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved,

marked container for all fuel purposes. Wipe up all fuel spills before starting saw.

SMove at least 10 feet (3 meters) from fuel- ing site before starting engine.

STurn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap

and refuel unit.

SStore the unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

KICKBACK

WARNING: Avoid kickback which can result in serious injury. Kickback is the backward, upward or sudden forward motion of the guide bar occurring when the saw chain near the upper tip of the guide bar con- tacts any object such as a log or branch, or when the wood closes in and pinches the saw chain in the cut. Contacting a foreign ob- ject in the wood can also result in loss of chain saw control.

SRotational Kickback can occur when the moving chain contacts an object at the up- per tip of the guide bar. This contact can cause the chain to dig into the object, which stops the chain for an instant. The result is a lightning fast, reverse reaction which kicks the guide bar up and back to- ward the operator.

SPinch-Kickbackcan occur when the the wood closes in and pinches the moving saw chain in the cut along the top of the guide bar and the saw chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation. The saw is driven straight back toward the operator.

S Pull-Incan occur when the moving chain contacts a foreign object in the wood in the cut along the bottom of the guide bar and the saw chain is suddenly stopped. This sudden stopping pulls the saw forward and away from the operator and could easily cause the operator to lose control of the saw.

Avoid Pinch-Kickback:

S Be extremely aware of situations or ob- structions that can cause material to pinch the top of or otherwise stop the chain.

SDo not cut more than one log at a time.

SDo not twist the saw as the bar is with- drawn from an undercut when bucking.

Avoid Pull-In:

SAlways begin cutting with the engine at full

speed and the saw housing against wood. S Use wedges made of plastic or wood.

Never use metal to hold the cut open.

Kickback Path

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 16/04 English Español FrançaisIdentification of Symbols Safety RulesPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Obstructions Clear The Working Area Kickback Safety FeaturesReduce the Chance of Kickback Maintain ControlComputed kickback angle CKA Table Chain Brake and CKA AngleChain Brake Nuts AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notCutters Adjusting the tensionChain Tension Including units with chain already installed Checking the tensionThrottle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationCutting Methods Starting a Warm EngineImportant Points Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Bucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing ServicePruning Limbing and Pruning Important PointsInspect Muffler and Spark Arresting Screen Cleaning the air filterCarburetor Adjustment BAR MaintenanceNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Ligations The U. S. EnvironmentalIntermediate 125 hours Extended 300 hours

2250, 2450, 2550, 2550 SE, 2555 specifications

The Poulan Pro chainsaw series, including the models 2250, 2450, 2550, 2550 SE, and 2555, represents a solid choice for both professionals and hobbyists in need of reliable cutting performance. Each model comes with distinct characteristics while sharing common technological innovations that define their functionality and efficiency.

The Poulan 2250 is designed for durability and ease of use. Weighing in at a manageable size, this chainsaw features a 50cc engine that delivers impressive power for a variety of cutting tasks. One of its standout features is the automatic oiler, which ensures that the chain is always lubricated, reducing wear and enhancing performance over time.

Next in line is the Poulan 2450, which further builds on the strengths of its predecessor. This model boasts a larger cutting capacity, facilitating challenges posed by thicker materials. It incorporates an easy-start system often appreciated by users who want to avoid the frustration of hard starts, making it a great option for regular maintenance tasks around the yard.

The Poulan 2550 exhibits an even greater commitment to power and efficiency. With a robust 45cc engine, this model effectively combines cutting power with manageable weight. It features an air filter system that promotes longer intervals between cleaning, making it easier for users to maintain the chainsaw in pristine working condition.

The Poulan 2550 SE takes the versatility up a notch. This model is equipped with an ergonomic design that reduces operator fatigue, especially during extended use. It also includes a specialized vibration dampening system, ensuring a more comfortable experience while cutting, which is particularly beneficial for professionals who rely on their equipment for hours on end.

Lastly, the Poulan 2555 combines all the best features from its predecessors while integrating advanced technologies to enhance user experience. This model is designed for straightforward maintenance, featuring tool-less access to the air filter and spark plug, making it easy for users to perform routine upkeep. Additionally, the 2555 is built with a powerful engine that delivers high torque, enabling efficient cutting of tougher materials.

Overall, the Poulan Pro chainsaw series embodies a tradition of reliability and innovation, suitable for a range of users, from casual gardeners to professional landscapers. With features like automatic oilers, ergonomic designs, and advanced air filtration systems, these chainsaws are tailored to meet the demands of various cutting applications, ensuring that users can tackle their tasks with confidence and ease.
Top Page Image Contents