Service, Pruning, Limbing | Poulan 2250, 2450, 2550, 2550 SE, 2555

Using a support stand

2nd Cut

1st Cut

2nd Cut

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your fist cut 1/3 of the way through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 -- 5 cm) collar from the truck of the tree.

Second cut

Third cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or ob- jects at the nose of the guide bar when limb- ing or pruning. Allowing such contact can re- sult in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, platforms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure foot- ing and balance.

S Watch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off balance. Use extreme caution when cutting small size limbs.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

SKeep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop- erly.

S Leave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and

limbs. Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

SRemove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . . Before each use For damaged parts . . . Before each use For loose caps . . . . . . Before each use For loose fasteners . . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

*Hours of Operation --

Each hour of operation is approximately 2 tanks of fuel.

AIR FILTER

CAUTION: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evapora- tive emissions.

2250, 2450, 2550, 2550 SE, 2555 specifications

The Poulan Pro chainsaw series, including the models 2250, 2450, 2550, 2550 SE, and 2555, represents a solid choice for both professionals and hobbyists in need of reliable cutting performance. Each model comes with distinct characteristics while sharing common technological innovations that define their functionality and efficiency.

The Poulan 2250 is designed for durability and ease of use. Weighing in at a manageable size, this chainsaw features a 50cc engine that delivers impressive power for a variety of cutting tasks. One of its standout features is the automatic oiler, which ensures that the chain is always lubricated, reducing wear and enhancing performance over time.

Next in line is the Poulan 2450, which further builds on the strengths of its predecessor. This model boasts a larger cutting capacity, facilitating challenges posed by thicker materials. It incorporates an easy-start system often appreciated by users who want to avoid the frustration of hard starts, making it a great option for regular maintenance tasks around the yard.

The Poulan 2550 exhibits an even greater commitment to power and efficiency. With a robust 45cc engine, this model effectively combines cutting power with manageable weight. It features an air filter system that promotes longer intervals between cleaning, making it easier for users to maintain the chainsaw in pristine working condition.

The Poulan 2550 SE takes the versatility up a notch. This model is equipped with an ergonomic design that reduces operator fatigue, especially during extended use. It also includes a specialized vibration dampening system, ensuring a more comfortable experience while cutting, which is particularly beneficial for professionals who rely on their equipment for hours on end.

Lastly, the Poulan 2555 combines all the best features from its predecessors while integrating advanced technologies to enhance user experience. This model is designed for straightforward maintenance, featuring tool-less access to the air filter and spark plug, making it easy for users to perform routine upkeep. Additionally, the 2555 is built with a powerful engine that delivers high torque, enabling efficient cutting of tougher materials.

Overall, the Poulan Pro chainsaw series embodies a tradition of reliability and innovation, suitable for a range of users, from casual gardeners to professional landscapers. With features like automatic oilers, ergonomic designs, and advanced air filtration systems, these chainsaws are tailored to meet the demands of various cutting applications, ensuring that users can tackle their tasks with confidence and ease.