Poulan 2250, 2550 Pinch-Kickback and Pull-In occur when, Avoid Pinch-Kickback, Avoid Pull-In

Page 3

Turntheengineoffandletsawcoolina non-combustiblearea,notondryleaves, straw,paper,etcSlowlyremovefuelcap. andrefuelunit.

Storetheunitandfuelinanareawhere fuelvaporscannotreachsparksoropen flamesfromwaterheaters,electricmotors orswitches,furnaces,etc.

KICKBACK

WARNING: Kickback can occur when

the moving chain contacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the saw chain in the cut. Contact at the upper portion of the tip of the guide bar can cause the chain to dig into the object, which stops the chain for an instant. The result is a light- ning fast, reverse reaction which kicks the guide bar up and back toward the operator.

If the saw chain is pinched along the top of the guide bar, the guide bar can be driven

rapidly back toward the operator. Either of these reactions can cause loss of saw con-

trol which can result in serious injury. Guard

against kickback.

Rotational Kickback is the rapid upward and backward motion of the chain sew that

can occur when moving saw chain near the upper portion of the tip of the guide bar contacts an object such as a log or branch.

Pinch-Kickback and Pull-In occur when

the chain is suddenly stopped by being pinched, caught, or by contacting a foreign

object in the wood. This sudden stopping of the chain results in a reversal of the chain

force used to cut wood and causes the saw

to move in the opposite direction of the chain rotation. Pinch-Kickback drives the

saw straight back toward the operator. Pull-

In pulls the saw away from the operator. Ei- ther reaction can result in loss of control and

serious injury.

Avoid Pinch-Kickback:

Be extremely aware of situations or ob- structions that can cause material to

pinch the top of or otherwise stop chain.

Do not cut more than one log at a time.

Do not twist the saw as the bar is with- drawn from an undercut when bucking.

Avoid Pull-In:

Always begin cutting with the engine at

full speed and the saw housing against wood.

Use wedges made of plastic or wood. Never use metal to hold the cut open.

OistruT

Clear The Working Area

REDUCE THE CHANCE OF

KICKBACK

Recognize that kickback can happen. With a basic understanding of kickback,

you can reduce the element of surprise which contributes to accidents.

Never let the moving chain contact any object at the tip of the guide bar.

Keep the working area free from obstruc- tions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting through a particular log or branch.

Keep your saw chain sharp and properly tensioned. A loose or dull chain can in-

crease the chance of kickback occurring.

Follow manufacturer's chain sharpening

and maintenance instructions. Check tension at regular intervals with the en-

g!ne stopped, never with the engine run- nmg. Make sure bar clamp nuts are se- curely tightened after tensioning chain.

Begin and continue cutting at full speed. If chain is moving at a slower speed, there is greater chance of kickback occurring.

Cut one log at a time.

Use extreme caution when re-entering a previous cut.

Do not attempt cuts starting with the tip of the bar (plunge cuts).

Watch for shifting logs or other forces that

could close a cut and pinch or fall into chain.

Use the Reduced-Kickback Guide Bar

and Low-Kickback Chain specified for your saw.

3

Image 3
Contents Poulan Handle Fuel with Caution Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderAvoid Pull-In KickbackPinch-Kickback and Pull-In occur when Avoid Pinch-KickbackMaintain Control Kickback Safety FeaturesPage BAR and Chain Lubrication Fueling EngineImportant Points Move switch to the Start or on positionDifficult starting or flooded engine For cold engine or warm engine after running out of fuelHinge holds tree on stump and helps control fall Plan a clear retreat pathFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or SUP- Port Stand Types of Cutting Used for BuckingBucking Without a Support Maintenance Schedule Removing a Pinched SAW a SAW Hung in the LOGLimbing Spark Plug BAR MaintenanceChain Sharpening Ignition TimingRanty Responsibilities LigationsManufac Turers WAR Ranty CoveragCovered. ADD-ON or Modified POULAN/WEED Eater Where To GETWarranty Service Warranty sewices Module, Maintenance Statement
Related manuals
Manual 17 pages 46.77 Kb