Installation Instructions, Switch S6 | Motorola MVME197LE specs

2

Hardware Preparation and Installation

Configuration Switch S6: Serial Port 4 Clock Select (S6-1, S6-2)

Serial port 4 can be configured to use clock signals provided by the RTXC4 and TRXC4 signal lines. Switch segments S6-1 and S6-2 on the MVME197LE configures serial port 4 to drive or receive TRXC4 and RTXC4, respectively. Factory configuration is with serial port 4 set to receive both signals (open). The remaining configuration of the clock lines is accomplished by using the Serial Port 4 Clock Configuration Select header on the MVME712M transition module. Refer to the MVME712M Transition Module and P2 Adapter Board User’s Manual for configuration of that header.

Switch S6

O			1					2
N

CLOSED

OPEN

Receive TRXC4

Receive RTXC4

(FACTORY CONFIGURATION)

Switch S6

O				1						2
N

CLOSED

OPEN

Drive TRXC4

Drive RTXCC4

Installation Instructions

The following sections discuss installation of the MVME197LE into a VME chassis, and system considerations. Ensure that BOOT ROM device is installed. Ensure that all switches are configured as desired.

2-6	Installation Guide

Image 38

Motorola MVME197LE manual Installation Instructions, Switch S6

Contents

MVME197LE Restricted Rights Legend Preface Document Terminology BIT Related Documentation Document Title Motorola Publication NumberPage Page Safety Summary Safety Depends on YOU Contents Hardware Preparation and Installation Using the 197Bug Debugger Appendix a Configure and Environment Commands List of Figures Xiv List of Tables Xvi Introduction Overview Requirements Features MVME197LE Specifications SpecificationsBlock Diagram Block Diagram Mezzanine Address Bus Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Memory Array Front Panel Switches and Indicators Functional Description Flash Memory Data Bus StructureMC88110 MPU Onboard Dram Interfaces Battery Backup RAM and ClockVMEbus Interface Serial Port Interface Printer Interface Ethernet Interface Scsi Interface Scsi Termination Peripheral Resources Interrupt Sources ConnectorsMemory Maps Processor Bus Memory Map Processor Bus Memory Map Dramsize Address Range Devices Accessed Port Size Local Devices Memory Map VMEbus Short I/O Memory Map VMEbus Accesses to the Local Peripheral BusVMEbus Memory Map Unpacking Instructions Hardware Preparation Hardware Preparation and Installation VMEbus Connector P1 Configuration Switch S1 General Information Configuration SwitchesSwitch S1 S1-1 to S1-8 OFF -- All Ones Factory Configuration Installation Instructions Switch S6 MVME197LE Module Installation System Considerations MVME197LEIG/D1 Hardware Preparation and Installation Overview of M88000 Firmware Description of 197Bug 197Bug Implementation Installation and Start-upComparison With M68000-Based Firmware Terminal to make sure XON/XOFF handshaking is enabled Ote Autoboot ROMboot Network Boot Reset Restarting the System Abort Break MPU Clock Speed Calculation Memory RequirementsSYSFAIL* Assertion/Negation Terminal Input/Output Control DEL Device Probe Function Disk I/O SupportBlocks Versus Sectors Disk I/O via 197Bug Commands Disk I/O via 197Bug System Calls Dskcfig Network I/O Support Default 197Bug Controller and Device ParametersDisk I/O Error Codes UDP/IP Protocol Modules Bootp Protocol ModulePhysical Layer Manager Ethernet Driver RARP/ARP Protocol Modules Multiprocessor Support Network Boot Control ModuleNetwork I/O Error Codes Multiprocessor Control Register Mpcr Method Mpar Diagnostic Facilities Gcsr Method Debugger General Information Entering Debugger Command Lines Debugger Syntactic Variables Expression as a Parameter Data Type Base Identifier Examples Offset Registers Address as a ParameterAddress Formats Entering and Debugging Programs Port Numbers 197Bug Vector Table and Workspace Calling System Utilities From User ProgramsPreserving The Debugger Operating Environment Hardware Functions Floating Point Support CPU/MPU Registers Scientific Notation Single Precision RealDouble Precision Real 197Bug Debugger Command Set Debugger Commands Nocm Noma Name Nioc RL Addrbhw Using the 197Bug Debugger Configure Board Information Block Cnfg MI Set Environment to Bug/Operating System ENV D Table A-1. ENV Command Parameters ENV Parameter and Options Default Meaning of Default Configure and Environment Commands Ffbffffc Table A-1. ENV Command Parameters Memory Requirement s 01FFFFFF Table A-1. ENV Command Parameters Efffffff FF7FFFFF Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters DISK/TAPE Controller Data Disk/Tape Controller Modules Supported MVME320 4 Devices Disk/Tape Controller Default ConfigurationsSingle Board Computers 7 Devices MVME323 4 Devices MVME327A 9 Devices MVME328 14 Devices MVME350 1 Device IOT Command Parameters for Supported Floppy Types IOT Parameter Disk/Tape Controller Data Network Controller Data Network Controller Modules Supported Network Controller Data Symbols Numerics IN-2 IN-3 Nvram A-2 XON/XOFF Index