Disk/Tape Controller Default Configurations | Motorola MVME197LE

Disk/Tape Controller Data

B	Disk/Tape Controller Default Configurations
B
			Single Board Computers - 7 Devices
			Single Board Computers - 7 Devices

		Controller	Address			Device LUN		Device Type
		LUN	Address			Device LUN		Device Type
		LUN


		0	$XXXXXXXX			00	SCSI Common Command Set (CCS),
						10	which may be any of these:
						20
						30	- Fixed direct access device
						40	- Removable flexible direct access
						50		(TEAC style)
						50	-	CD-ROM
						60	-	CD-ROM
						60	-	Sequential access device
							-	Sequential access device

				MVME320 - 4 Devices

		Controller	Address			Device LUN		Device Type
		LUN	Address			Device LUN		Device Type
		LUN


		11	$FFFFB000			0	Winchester hard drive
						1	Winchester hard drive
						2	5-1/4” DS/DD 96 TPI floppy drive
		12	$FFFFAC00			2	5-1/4” DS/DD 96 TPI floppy drive
		12	$FFFFAC00			3	5-1/4” DS/DD 96 TPI floppy drive
						3	5-1/4” DS/DD 96 TPI floppy drive

				MVME323 - 4 Devices

		Controller	Address			Device LUN		Device Type
		LUN	Address			Device LUN		Device Type
		LUN


		8	$FFFFA000			0	ESDI Winchester hard drive
						1	ESDI Winchester hard drive
						2	ESDI Winchester hard drive
		9	$FFFFA200			2	ESDI Winchester hard drive
		9	$FFFFA200			3	ESDI Winchester hard drive
						3	ESDI Winchester hard drive

B-2	Installation Guide

Image 90

Motorola MVME197LE manual Disk/Tape Controller Default Configurations, Single Board Computers 7 Devices, MVME320 4 Devices

Contents

MVME197LE Restricted Rights Legend Preface Document Terminology BIT Related Documentation Document Title Motorola Publication NumberPage Page Safety Summary Safety Depends on YOU Contents Hardware Preparation and Installation Using the 197Bug Debugger Appendix a Configure and Environment Commands List of Figures Xiv List of Tables Xvi Introduction Overview Requirements Features Specifications Block DiagramMVME197LE Specifications Block Diagram Mezzanine Address Bus Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Memory Array Front Panel Switches and Indicators Functional Description Flash Memory Data Bus StructureMC88110 MPU Onboard Dram Interfaces Battery Backup RAM and ClockVMEbus Interface Serial Port Interface Printer Interface Ethernet Interface Scsi Interface Scsi Termination Peripheral Resources Interrupt Sources ConnectorsMemory Maps Processor Bus Memory Map Processor Bus Memory Map Dramsize Address Range Devices Accessed Port Size Local Devices Memory Map VMEbus Accesses to the Local Peripheral Bus VMEbus Memory MapVMEbus Short I/O Memory Map Unpacking Instructions Hardware Preparation Hardware Preparation and Installation VMEbus Connector P1 Configuration Switches Switch S1Configuration Switch S1 General Information S1-1 to S1-8 OFF -- All Ones Factory Configuration Installation Instructions Switch S6 MVME197LE Module Installation System Considerations MVME197LEIG/D1 Hardware Preparation and Installation Overview of M88000 Firmware Description of 197Bug Installation and Start-up Comparison With M68000-Based Firmware197Bug Implementation Terminal to make sure XON/XOFF handshaking is enabled Ote Autoboot ROMboot Network Boot Reset Restarting the System Abort Break Memory Requirements SYSFAIL* Assertion/NegationMPU Clock Speed Calculation Terminal Input/Output Control DEL Disk I/O Support Blocks Versus SectorsDevice Probe Function Disk I/O via 197Bug Commands Disk I/O via 197Bug System Calls Dskcfig Default 197Bug Controller and Device Parameters Disk I/O Error CodesNetwork I/O Support UDP/IP Protocol Modules Bootp Protocol ModulePhysical Layer Manager Ethernet Driver RARP/ARP Protocol Modules Multiprocessor Support Network Boot Control ModuleNetwork I/O Error Codes Multiprocessor Control Register Mpcr Method Mpar Diagnostic Facilities Gcsr Method Debugger General Information Entering Debugger Command Lines Debugger Syntactic Variables Expression as a Parameter Data Type Base Identifier Examples Address as a Parameter Address FormatsOffset Registers Entering and Debugging Programs Port Numbers 197Bug Vector Table and Workspace Calling System Utilities From User ProgramsPreserving The Debugger Operating Environment Hardware Functions Floating Point Support CPU/MPU Registers Single Precision Real Double Precision RealScientific Notation 197Bug Debugger Command Set Debugger Commands Nocm Noma Name Nioc RL Addrbhw Using the 197Bug Debugger Configure Board Information Block Cnfg MI Set Environment to Bug/Operating System ENV D Table A-1. ENV Command Parameters ENV Parameter and Options Default Meaning of Default Configure and Environment Commands Ffbffffc Table A-1. ENV Command Parameters Memory Requirement s 01FFFFFF Table A-1. ENV Command Parameters Efffffff FF7FFFFF Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters Table A-1. ENV Command Parameters DISK/TAPE Controller Data Disk/Tape Controller Modules Supported MVME320 4 Devices Disk/Tape Controller Default ConfigurationsSingle Board Computers 7 Devices MVME323 4 Devices MVME327A 9 Devices MVME328 14 Devices MVME350 1 Device IOT Command Parameters for Supported Floppy Types IOT Parameter Disk/Tape Controller Data Network Controller Data Network Controller Modules Supported Network Controller Data Symbols Numerics IN-2 IN-3 Nvram A-2 XON/XOFF Index