Poulan 2250, 2450, 2550 Reduce the Chance Kickback, Avoid Pinch---Kickback, Avoid Pull---In

Page 3

STurn the engine off and let saw cool in a non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap and refuel unit.

S Store the unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

KICKBACK

WARNING: Kickback can occur when

the moving chain contacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the saw chain in the cut. Contact at the upper portion of the tip of the guide bar can cause the chain to dig into the object, which stops the chain for an instant. The result is a light- ning fast, reverse reaction which kicks the guide bar up and back toward the operator. If the saw chain is pinched along the top of the guide bar, the guide bar can be driven rapidly back toward the operator. Either of these reactions can cause loss of saw con- trol which can result in serious injury. Guard against kickback.

Rotational Kickback is the rapid upward and backward motion of the chain saw that can occur when moving saw chain near the upper portion of the tip of the guide bar contacts an object such as a log or branch. Pinch-Kickback and Pull-In occur when the chain is suddenly stopped by being pinched, caught, or by contacting a foreign object in the wood. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation. Pinch-Kickback drives the saw straight back toward the operator. Pull- In pulls the saw away from the operator. Ei- ther reaction can result in loss of control and serious injury.

Avoid Pinch---Kickback:

SBe extremely aware of situations or ob- structions that can cause material to pinch the top of or otherwise stop chain.

Do not cut more than one log at a time.S

S Do not twist the saw as the bar is with- drawn from an undercut when bucking.

Avoid Pull---In:

S Always begin cutting with the engine at full speed and the saw housing against wood.

S Use wedges made of plastic or wood. Never use metal to hold the cut open.

Kickback Path

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF

KICKBACK

S Recognize that kickback can happen. With a basic understanding of kickback, you can reduce the element of surprise which contributes to accidents.

S Never let the moving chain contact any object at the tip of the guide bar.

S Keep the working area free from obstruc- tions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting through a particular log or branch.

S Keep your saw chain sharp and properly tensioned. A loose or dull chain can in- crease the chance of kickback occurring. Follow manufacturer’s chain sharpening and maintenance instructions. Check tension at regular intervals with the en- gine stopped, never with the engine run- ning. Make sure bar clamp nuts are se- curely tightened after tensioning chain.

S Begin and continue cutting at full speed. If chain is moving at a slower speed, there is greater chance of kickback occurring.

S Cut one log at a time.

S Use extreme caution when re-entering a previous cut.

S Do not attempt cuts starting with the tip of the bar (plunge cuts).

SWatch for shifting logs or other forces that could close a cut and pinch or fall into chain.

Use the Reduced---Kickback Guide BarS

and Low---Kickback Chain specified for your saw.

3

Image 3
Contents 2250 / 2450 Handle Fuel with Caution Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderAvoid Pull---In KickbackReduce the Chance Kickback Avoid Pinch---KickbackMaintain Control Attaching the BAR & Chain If not BAR and Chain Lubrication Adjusting the tensionChecking the tension Fueling EngineImportant points to remember Important PointsTree Felling Techniques Plan a clear retreat path Felling Large Trees 6 inches in diameter or largerNotch CUT and Felling the Tree Cutting a Fallen TreeBucking Using a LOG or SUP- Port Stand Types of Cutting Used for BuckingBucking Without a Support Removing a Pinched SAW LimbingPruning Ignition Timing BAR MaintenanceAIR Filter Chain SharpeningPage Related Parts Any POULAN/WEED Warranty Service Warranty services