Poulan 115267626 instruction manual Adjusting the tension, Cutters, Adjusting Screw

Page 7

Bar bolts

Guide bar

6.Carefully remove the chain from the pack- age. Hold chain with the drive links as shown.

Tip of

Bar

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

7.Place chain over and behind clutch re- tainer, fitting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

11.Now, install clutch cover making sure the adjusting pin is positioned in the low- er hole in the guide bar. Remember this pin moves the bar forward and back- ward as the screw is turned.

Clutch

Cover

Adjusting Pin Lower

Hole

Guide Bar

12.Install bar nuts and finger tighten only. Once the chain is tensioned, you will need to tighten bar nuts.

CHAIN TENSION (Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

Bar

Chain Adjustment

Bar Nuts Adjusting Tool

Screw (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

1.Loosen bar nuts until they are finger tight against the clutch cover.

2.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Adjusting

Screw

3.Using bar tool, roll chain around guide bar to ensure all links are in bar groove.

4.Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn ad- justing screw 1/4 turn clockwise. Repeat until sag does not exist.

Adjusting Screw -- 1/4 Turn

5.While lifting tip of guide bar, tighten bar nuts securely with the bar tool.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Using the chain sawAlways use two hands when operating the chain saw Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pinch-Kickback Kickback Safety FeaturesReduce the Chance of Kickback Maintain ControlChain saws as set by Ansi B175.1 Chain Brake and CKA AngleAttaching the BAR & Chain If not AssemblyAdjusting Screw Adjusting the tensionCutters Operation Fuel Requirements Chain BrakeChain Tension Before Starting Engine Fueling EngineStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Tree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsImportant Points Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Check Guide BARTo Sharpen Chain Cleaning the Spark ARREST- ING ScreenChain Adjustment Replace Spark PlugCooling System Carburetor AdjustmentStorage Idle Speed-TOther Load Adjustment EngineFuel System EnginePoulan PRO Charlotte, NC Canada, contactLigations The U.S. Environmental
Top Page Image Contents