Rhino Mounts GK6072 manual Following rules

Page 11
(SG-22)
(SG-21)
(SG-19)

SAFETY

WARNING! Transport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condi- tion and operate properly.

Before transporting the Tractor and Implement, determine the safe transport speeds for you and the equipment. Make sure you abide by

the following rules:

1.Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement.

As you increase the speed of the Tractor the stopping distance increases. Determine the maximum safe transport speed for you and this Equipment.

2.Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that it is safe to operate at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum safe turning speed for you and this equipment before operating on roads or uneven ground.

3.Only transport the Tractor and Implement at the speeds that you have determined are safe and which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you andwatch out for the other guy.

SAFETY

WARNING!

WARNING!

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is off before working on the Implement.

(SG-20)

Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.

WARNING!

DANGER!

Always read carefully and comply fully with the manufacturers instruc- tions when handling oil, solvents, cleansers, and any other chemical agent.

Never run the tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

GK6072 08/01

Safety Section 1-5

© 2004 Alamo Group Inc.

 

Image 11
Contents GK6072 To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroFalling off can result in serious injury or death Following rules Drugs or alcohol. SG-27 GK6072 08/01 Alamo Group Inc Wait a minute...Save a life Stop Mowing if Passersbyare Within 100 Yards Unless See Your SERVIS-RHINO Dealer Parts InformationQTY Level Description 14ANot Shown Page Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Frame Attachment Exceed Horsepower Recommendations Dealer SET-UP InstructionsStandard Position Extended Position Caster Wheel Attachments Page Operation Section Attaching Mower to Tractor Lift Type OperationStarting & Stopping Cutter Cutting Height AdjustmentDriveline Attachment to Tractor Detaching and Storing Cutting SpeedCutting Tips Before Operating or Transporting this Mower Driveline Length Check ProcedureFront Gauge Wheel Interference Check Driveline LengthStreaking Problem Possible Cause RemedyDamaged Belt Maintenance Section Description Frequency Lubrication InformationLubrication Fitting Location Gauge Wheel Assemblies GearboxBlade Spindle Lubrication Driveline LubricationBlade Removal Blade InstallationBlade Servicing Blade SharpeningMaintenance Proper Torque for Fasteners StorageMaintenance Servicing Driveline Shields Figure SERVIS-RHINO To the OWNER/OPERATOR/DEALER GK60/72-OMWPL-08/01 00767471C Printed U.S.A RHINO-SERVIS SERVIS-RHINOWARRANTY Registration Information Page Dealer Copy Page Customer Copy