Scag Power Equipment MAG manual Signal Words, Before Operation Considerations

Page 4

Section 2

SAFETY INFORMATION

2.1 INTRODUCTION

Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all the controls before operating the mower.

READ THIS OPERATOR’S MANUAL BEFORE ATTEMPTING TO START YOUR MOWER.

A replacement manual is available from your authorized Scag Service Dealer or by Contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050. There is nominal charge of $2.00 for each manual. Please indicate the complete model and serial number of your Scag product.

2.2 SIGNAL WORDS

This symbol means “Attention! Become Alert! Your

Safety is Involved!" The symbol is used with the following signal words to attract your attention to safety messages found on the decals and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death.

Signal Word:

It is a distinctive word on safety decals and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.

The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irreparable injury if proper precautions are not taken.

WARNING:

The signal word “WARNING” denotes a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.

CAUTION:

The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken.

Your safety and the safety of others depend significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.

2.3BEFORE OPERATION CONSIDERATIONS

1.NEVER allow children to operate this riding mower. Do not allow adults to operate this machine without proper instructions.

2.DO NOT mow when children and/or others are present.

3.Clear the area to be mowed of objects that could be picked up and thrown by the cutter blades.

4.DO NOT carry passengers.

5.DO NOT wear loose fitting clothing that could get caught in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. Wearing safety glasses, safety shoes and a helmet is advisable and is required by some local ordinances and insurance regulations.

2

Image 4
Contents Operators Manual Remember Your Mower is only AS Safe AS the Operator Direction Reference IntroductionServicing the Engine and Drive Train Components Signal Words Before Operation ConsiderationsOperation Considerations Maintenance Considerations Safety and Instructional Decals Keep Clear Contact can InjureElectrical EngineTractor Weights and Dimensions Tractor ContdCutter Deck Hydraulic SystemOperating Instructions Controls and Instrument IdentificationLevers Safety Interlock System Diesel Engine BREAK-IN Operator Comfort AdjustmentsStarting the Diesel Engine Seat Adjustment Adjusting Ground Speed and DirectionEngaging the Mower Hillside OperationStopping After OperationMoving Mower with the Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Tilting the Mower Deck 11 Mower Cutting Height GaugeTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Troubleshooting Parking Brake Adjustment FORWARD/REVERSE Neutral AdjustmentFAN Belt Adjustment Throttle Control Linkage AdjustmentCutter Brake Linkage Pump Drive Belt Adjustment Electric Clutch Drive Belt AdjustmentCutter Drive Belt Adjustments Alternator Belt AdjustmentCutter Deck Adjustments Belt AlignmentBlade Cutting Height Adjustment 11 Measuring Cutting Edge HeightMAG-61, MAG-72 Cutter Deck Ref. Part Mag Mag Number Description Descripton MAG-61, MAG-72 Deck Support MAG-61, MAG-72 Cutter Deck Support Rider Frame Part Number Description Engine Deck Engine Deck RADIATOR/OIL Cooler RADIATOR/OILCOOLER Muffler and AIR Cleaner Ref. Part No. Number Description Deck Drive System Part Number Description Pump and FAN Drive Systems Part Ref. Part Number Description No. Number Instrument Panel Ref. Number Description Wiring Harness and Electrical Components Switch, Ignition Cutter Brake Linkage Grip, Clutch Lever Parking Brake Linkage 48093 Grip, Handle 45716 Throttle Linkage 481243 FORWARD/REVERSE Linkage Bolt, Neutral Adjustment, 3/8-24 x 6-3/4 Fuel Tank and Lines 46933 Hydraulic Circuits Ref. Part Number Description Control Panel Heavy Duty Commercial Grease Fitting Lubrication Chart Page Engine Tractor Contd Limited WARRANTY-COMMERCIAL Equipment 1996