Scag Power Equipment SWZ36A-17KAI, SWZ52V-19KAI, SWZ-19KAI, SWZ48V-17KAI Using a spark arrestor

Page 10

R

Section 2

3.Remove spark plug wire before making any repairs.

4.Keep all nuts, bolts and screws tight, to ensure the machine is in safe working condition. Check blade mounting bolts frequently to be sure they are tight.

5.Do not change the engine governor settings or overspeed the engine. See the engine operator's manual for information on engine settings.

6.To reduce fire hazard, keep the cutting units, drives, muffler and engine free of grass, leaves, excessive grease, oil and dirt.

7.Park the machine on level ground.

8.NEVER allow untrained personnel to service the machine.

9.Use care when checking blades. Use a Blade Buddy, wrap the blade(s) or wear gloves and USE CAUTION when servicing blades. Only replace blades. NEVER straighten or weld blades.

10.Keep all parts in good working condition. Replace all worn or damaged decals.

11.Use jack stands to support components when required.

12.Carefully release pressure from components with stored energy.

13.Let the engine cool before storing.

14.DO NOT store the machine near an open flame.

15.Shut off fuel while storing or transporting.

16.DO NOT store fuel near flames or drain indoors.

2.6 Using a spark arrestor

The engine in this machine is not equipped with a spark arrestor muffler. It is in violation of California Public Resource Code Section 4442 to use or operate this engine on or near any forest covered, brush covered or grass covered land unless the exhaust system is equipped with a spark arrestor meeting any applicable local or state laws. Other states or federal areas may have similar laws. Check with your state or local authorities for regulations pertaining to these requirements.

6

Image 10
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Following SectionDirection Reference General InformationIntroduction Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionSignal Words Safety InformationBefore Operation considerations Operation Considerations Maintenance Considerations & storage Using a spark arrestor Falling HAzARD USE only Scag APPROvED Safety and Instructional DecalsInstall Belt COvER Before Riding AttachmentsElectrical SpecificationsEngine Engine Deck61v Weights and Dimensions 36ACutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationStarting the Engine Safety Interlock SystemInitial RUN-IN Procedures Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter BladesReverse Travel After Operation Hillside OperationParking the Mower Removing Clogged MaterialMoving Mower with Engine Stopped Recommendations for MowingTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Neutral adjustment AdjustmentsParking brake adjustment AdjustmentsThrottle Control and Choke Adjustments Tracking adjustmentCutter Deck Belt Adjustments Adjusting Cutting Height Belt AlignmentBlade Height Adjustment Custom-Cut Baffle AdjustmentCustom-Cut Baffle Adjustment Mounting Slot Selected Electric clutch adjustment 11. Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic Oil Filter ElementEngine Oil Engine Fuel SystemCleaning and/or Replacing Air Cleaner Element Engine Air CleanerBattery eLECTRIC Start Models Charging the BatteryBlade Inspection Cutter BladesJump Starting Blade SharpeningBlade Replacement TiresIllustrated Parts List Scag Approved Attachments and AccessoriesCaster Assembly 36A Cutter Deck 23A 462030 48V & 52V Cutter Decks 48V & 52V Cutter Decks 61V Cutter Deck 04040-04 Flatwasher, 5/16 Engine Deck Manual Start 16KAI 17KAI 19KAI Engine Deck Electric Start Battery Not Available Through Scag Drive and Brake Components 04001-151 Bolt, Hex Head 3/8-16 x Handle Assembly 16 Small Frame 461965 Handle Assembly 20 Large Frame 48798 Hydraulic Assembly Screw, 1/4-20 x 2.0 Round Head Phillips Hydraulic Pump Assembly Housing Kit 15 HP 15 HP, 16 HP & 17 HPHandle Wiring Harness Kawasaki Electric Start Wire Harnesses Wire Harness Adapter Kawasaki Replacement Decals and Information Plates Heavy-Duty Commercial Cutting Height Adjustment Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Opcionales ARTÍCULOS/ACCESORIOS Técnicas Especificaciones Transmisión DE SistemaCorte DE Condiciones LAS EN Fallas DE Identificación Lo a inclinadas Salientes Corte deTrayectoria la de ancho IrregularCortar sin césped CorteDe trayectorias entre De Franjas VetasPrecaución Máquina LA DE LimpiezaEléctrico Arranque DE Unidades Sólo Batería Continuación Hidráulico SistemaHidráulico Sistema NotaMantenimiento Y Lubricación Alineación DE Ajuste Cualquier Realizar DE Tratar DE Antes Alineación DE AjusteDirección DE Control ContinuaciónNeutral Ajuste Neutral Ajuste .12 FiguraContinuacion Corte DE Cuchillas Corte de deflector del Posición .9 FiguraCorte DE Altura LA DE Ajuste Corte DE CuchillasCorte DE Plataforma LA DE Ajustes Precaución Cortacésped DEL Operación Está motor el Si .necesario sea según EstranguleUSO DE DÍA Primer Cortacésped DEL OperaciónHoras 10 Aproximadamente Inicial Arranque DE ProcedimientosGiratorias Cuchillas Almacenamiento MantenimientoOperación DE Consideraciones DE Consideraciones OperaciónLA a Previas Consideraciones Advertencia Operación LA a Previas ConsideracionesOperación Seguridad DE General InformaciónLento Rápido ISO Símbolos Instrucciones DE Referencia IntroducciónScag POR Aprobados Aditamentos Y Accesorios 21KAE-SWZ Página TemaSeñalización de Palabras 21KAE-SWZ 61V-SWM52V-SWM 19KAI-SWZManual DEL Operador