Scag Power Equipment STT61V-31KB-DF manual Sheet Metal Components

Page 51

Section 8

			SHEET METAL COMPONENTS
	Ref.	Part No.	Description
	No.	Part No.	Description
	No.
	1	04001-145	Bolt, Hex Head 1/2-13 x 3.5”
	2	41020	Weight
	3	04021-07	Nut, Hex Elastic Stop 1/2-13
	4	481284	Bumper, Rubber 5/16-18 x 5/8”
	5	462330	Main Frame Assembly w/Decals
	6	424847	Foot Plate
	7	04001-19	Bolt, Hex Head 3/8-16 x 1”
	8	04041-07	Flatwasher, 3/8-.391 x .938 x .105

904019-03 Nut, Hex Serrated Flange 5/16-18

1004001-45 Bolt, Hex Head 3/8-16 x 2.0”

11	04021-09	Nut, Elastic Stop 3/8-16
12	43606	Spacer Bushing
13	491729	Seat Plate Weldment w/Decal
14	452026	Fender Weldment, RH
15	04003-01	Bolt, Carriage 1/4-20 x 6”
16	*	Battery (not avail. through Scag)
17	422682	Cover, Battery
18	04003-12	Bolt, Carriage 5/16-18 x 3/4”
19	462007	Plate, Battery Box
20	48661	Rubber Pad
21	04029-01	Wing Nut, 1/4-20 x 3/4”
22	04021-09	Nut, Elastic Stop 3/8-16
23	424488	Battery Box Mount

2404001-19 Bolt, Hex Head 3/8-16 x 1”

2504019-04 Nut, Hex Serrated Flange 3/8-16

2604017-27 Screw, Hex Serrated Flange 3/8-16 x 1”

27	452025	Fender Weldment, LH
28	04021-09	Nut, Hex Elastic Stop 3/8-16
29	04021-11	Nut, Elastic Stop 7/16-14
30	04030-05	Lockwasher, 7/16”
31	04001-28	Bolt, Hex Head 7/16-14 x 1-1/4”
32	452202	Extention Weldment, Caster (Use with 61” Deck)
33	484195	Cap, Grease
34	04021-20	Nut, Hex Elastic Stop 1.0”-14
35	481657	Bearing W/Race
36	481025	Seal, 2.00” OD. x 1.625” Bore
37	04021-07	Nut, Hex Elastic Stop 1/2-13
38	43584	Spacer, Caster Wheel
39	43583	Sleeve, Caster Wheel (61V)
40	04001-167	Bolt, Hex Head 1/2-13 x 9-1/2” (61V)
41	451416	Yoke Weldment, Caster (61V )
42	482028-01	Plug, 1/4-28 THD Form
43	92785	Wheel Assembly, (Inc. 44, 45, & 46)
44	482622	Seal
45	482621	Bearing w/ Race
46	48114-10	Grease Fitting
47	424999	Bracket, Fender Support

4804001-32 Bolt, Hex Head 3/8-16 x 1-1/4"

4904019-05 Nut, 7/16-14 Serrated Flange

50	04050-01	Retaining Ring .625" Ext. "E"
51	483371	Spring, Seat Latch
52	491731	Lever Assembly, Seat Release
53	484341	Grip, Seat Latch
54	04001-117	Bolt, Hex Head 7/16-14 x 1-3/4"
55	48566	Cable, Seat Stop
56	04001-02	Bolt, Hex Head, 1/4-20 x 1-1/4"
57	04019-02	Nut, Hex Serrated Flange 1/4-20

47

R

Image 51

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Following Section Troubleshooting Cutting Conditions AdjustmentsServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSafety Information Signal WordsBefore Operation considerations Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSPARK Ignition System Forward R F REvERSE Install Belt COvER BeforeElectrical SpecificationsPower Head EngineProductivity Weights And DimensionsCutter Deck Hydraulic SystemControls And Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Initial Run-In ProceduresStarting The Engine Ground Travel And SteeringReverse Travel Engaging The Deck Drive Cutter BladesAfter Operation Rotating BladesHillside Operation Parking The MowerAdjusting Cutting Height Moving Mower With Engine StoppedRecommendations For Mowing Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control and Choke AdjustmentsCutter Deck Pitch Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilLpg fUel system Replacing In-Line Fuel Filter ElementsEngine Air Cleaner BatteryCleaning and/or Replacing Air Cleaner Element Cutter Blades Drive BeltsBlade Sharpening Blade ReplacementTires Cutter Deck GearboxCooling System Cleaning the Radiator Debris Screen Body, Deck, And UpholsteryChecking The Fan Belt Tension Liquid- Cooled Engines Only Scag Approved Attachments and Accessories Illustrated Parts ListSection 61V Cutter Deck Section 61V Cutter Deck Cutter Deck Controls Description Sheet Metal Components Sheet Metal Components STT ROLL-OVER Protection System STT ROLL-OVER Protection System STT Suspension Seat Section Deck Drive Components Bolt, Hex Head 5/16-18 x 1-3/4 Grd Engine & Attaching Parts Kubota Dual Fuel Available through the individual engine manufacturer Brake and Steering Components Brake and Steering Components Hydraulic System Kubota Dual Fuel Hydraulic System Kubota Dual Fuel STT-DF Gasoline System STT-DF Gasoline System STT-DF LP System Regulator, Kubota Section BDP-16A Hydraulic Pump Assembly with Cooling Fan Hex Screw, Flanged Head M10 x 1.50-65mm Electrical System Kubota Dual Fuel Fuel Pump Heavy-Duty Commercial Replacement Decals and Information PlatesDUAL-FUEL Electrical Schematic Kubota Dual Fuel Limited Warranty Commercial Equipment