Scag Power Equipment STT61V-31KB-DF manual Description

Page 49

Section 8

CUTTER DECK CONTROLS

	Ref.	Part No.	Description
	No.	Part No.	Description
	No.
	1	481764	Link, Deck Lift

204020-28 Nut, Jam 1/2-20 LH

3481766 Rod End, Female - 1/2-20 LH

404050-10 Ring, Retaining 1/2” External “E”

5	45905	Bellcrank Weldment, RH Rear
6	43487	Pin, Decklift
7	482429	Slide Weldment, Height Adjustment

804009-02 Bolt, Shoulder 1/2 x 3/4”

948100-14 Bushing, .502 ID.

10481428 Grip, Deck Latch

11462102 Deck Latch (Includes items 9 & 10)

12

424857

Lockplate, Decklift

1304014-03 Screw, Cap 5/16-18 x 3” FHHS

1404019-04 Nut, Hex Serrated Flange 3/8-16

15	423509	Guide, Long
16	04003-04	Bolt, Carriage 5/16-18 x 1”
17	422381	Guide, Short
18	423463	Bracket, Cutting Height Adjustment

1904001-20 Bolt, Hex Head 3/8-16 x 1-1/2”

2004019 -03 Nut, Hex Serrated Flange 5/16-18

21	481598	Spring, Helper (61” & 72” Cutter Decks Only)
22	48114-04	Grease Fitting
23	43526	Swivel Joint, LH
24	04020-09	Nut, Hex 5/8-11

2504040-09 Flatwasher, 5/8” (.656 x 1.312 x .095)

2604061-07 Cotter Pin, 3/16 x 1”

27	45904	Bellcrank Weldment, LH Rear
28	48540	Chain

2904004-48 Stud, 5/8-11 x 26.0”

30461929 Lever Assembly, Deck Level

31

43527

Swivel Joint, RH

3204021-05 Locknut, 3/8-16 Center Lock

3304050-08 Ring, Retaining 1” External “E”

3404041-14 Flatwasher, 1” (1.062 x 1.50 x .048)

35481547 Lanyard, Deck Height Pin

3604067-09 Ring Pin, 1/2 x 3.06”

3704021-09 Nut, 3/8-16 Elastic Stop

38424504 Foot Pedal, Height Adjustment

3904021-07 Nut, Hex Elastic Stop 1/2-13

4004030-07 Lockwasher, 5/8”

4104105-01 Capscrew, 5/8-11 x 1-1/2”

42481765 Rod End, Female - 1/2-20 RH

4304001-74 Bolt, Hex Head 1/2-13 x 3”

4404020-27 Nut, Jam 1/2-20 RH

45

43391

Spacer, Decklift Pedal

45

R

Image 49

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Following Section Troubleshooting Cutting Conditions AdjustmentsIntroduction General InformationDirection Reference Servicing The Engine And Drive Train ComponentsSymbol Description SymbolsSignal Words Safety InformationBefore Operation considerations Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Using a spark arrestor Maintenance Considerations & storageSPARK Ignition System Forward R F REvERSE Install Belt COvER BeforePower Head SpecificationsEngine ElectricalCutter Deck Weights And DimensionsHydraulic System ProductivityControls And Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemStarting The Engine Initial Run-In ProceduresGround Travel And Steering Forward TravelReverse Travel Engaging The Deck Drive Cutter BladesHillside Operation Rotating BladesParking The Mower After OperationMoving Mower With Engine Stopped Adjusting Cutting HeightRecommendations For Mowing Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control and Choke AdjustmentsCutter Deck Pitch Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilLpg fUel system Replacing In-Line Fuel Filter ElementsBattery Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Cutter Blades Drive BeltsBlade Sharpening Blade ReplacementCutter Deck Gearbox TiresCooling System Body, Deck, And Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Liquid- Cooled Engines Only Scag Approved Attachments and Accessories Illustrated Parts ListSection 61V Cutter Deck Section 61V Cutter Deck Cutter Deck Controls Description Sheet Metal Components Sheet Metal Components STT ROLL-OVER Protection System STT ROLL-OVER Protection System STT Suspension Seat Section Deck Drive Components Bolt, Hex Head 5/16-18 x 1-3/4 Grd Engine & Attaching Parts Kubota Dual Fuel Available through the individual engine manufacturer Brake and Steering Components Brake and Steering Components Hydraulic System Kubota Dual Fuel Hydraulic System Kubota Dual Fuel STT-DF Gasoline System STT-DF Gasoline System STT-DF LP System Regulator, Kubota Section BDP-16A Hydraulic Pump Assembly with Cooling Fan Hex Screw, Flanged Head M10 x 1.50-65mm Electrical System Kubota Dual Fuel Fuel Pump Heavy-Duty Commercial Replacement Decals and Information PlatesDUAL-FUEL Electrical Schematic Kubota Dual Fuel Limited Warranty Commercial Equipment