Remington Power Tools 107625-02, 107624-02, 111174-01 owner manual Assembly

Page 9

ASSEMBLY

Note: Some models are pre-assembled. Assembly is not needed on these models. See Saw Chain Ten- sion Adjustment.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

IMPORTANT: Do not clamp chain saw in vise during assembly.

1.Lay chain out flat.

2.Loosen and remove guide bar nuts and sprocket cover.

3.Loosen and remove drive sprocket screw or re- move E-ring from shaft (see Figure 4). Remove sprocket support.

4.Install guide bar onto saw body. Assemble center slot of guide bar onto guide bar bolts.

5.To replace sprocket support, repeat step 3 in re- verse order. Firmly tighten drive sprocket screw with #2 Phillips screwdriver (if applicable).

6.Place chain around drive sprocket, along top groove of guide bar, and around guide bar nose. Note: Make sure cutting edges of chain are fac- ing in right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 4, and indicator on side cover of saw).

CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut.

7.Insert tab of sprocket cover into slot on side cover and rotate sprocket cover onto guide bar bolts until sprocket cover rests against guide bar.

8.Place guide bar nuts, removed in step 2, over guide bar bolts.

IMPORTANT: Tighten guide bar nuts finger tight only.

9.Turning chain tensioning knob (Model 107625 -02, 111174-01) or chain tensioning screw (Model 107624-02), adjust position of adjust- ment block until it is aligned and inserted into the round adjusting hole on guide bar (see Figure 4, 5and 6). Turning chain tensioning knob or chain tensioning screw counterclockwise will move adjustment block to rear of guide bar. Turning chain tensioning knob or chain tensioning screw clockwise will move adjustment block to front of guide bar.

10.If needed, readjust guide bar nuts to finger tight only.

11.Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment.

ENGLISH

Drive Sprocket

Sprocket Support

Guide Bar Bolts

Drive Sprocket Screw or E-Ring

Guide Bar

Sprocket Cover

 

 

 

Saw Chain

 

Adjusting

Towards Guide Bar Nose

 

Hole

Guide Bar Nuts

 

 

 

 

 

 

 

Cutting Edge

Figure 4 - Assembling Guide Bar and Chain

 

Adjustment

Adjustment Block

E-Ring

Chain Tensioning Knob

 

Block

 

 

 

 

 

Chain Tensioning Screw

Figure 6 - Turn Chain Tensioning Knob on Model

 

 

Figure 5 - Turn Chain Tensioning Screw on

Model 107624-02

107625-02, 111174-01

 

 

 

 

9

www.remingtonpowertools.com

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Models EL-8 107624-02, 107625-02 Electric Chain SAWCall 1-800-626-2237 for Technical Assistance Stop Para ArrétContents Important Safety Information Before Operating SAWWhile Operating SAW Kickback Kickback Safety Devices On This SawSaw Maintenance and Kickback Safety Maintenance and Storage of Chain SAWUnpacking Chain Saw Model Product IdentificationChain SAW Names and Terms Important Do not clamp chain saw in vise during assembly AssemblyTo tension saw chain To tension saw chain orPull chain to check tension. Guide Links should not come out of guideFilling OIL Tank Operating Chain SAWOiling Chain Extension CordsCutting with the Chain SAW Felling a Tree Cutting Down a TreeBefore Felling a Tree Felling Cut Felling Procedure Felling NotchLimbing a Tree Bucking a LOGEntire Length Of Log On Ground Log Supported On One End Log Supported On Both EndsTrimming a Tree Pruning Cleaning SAW Body Cleaning and MaintenanceNormal Guide Bar Maintenance Care of Guide BARItems Needed to Sharpen Chain Cleaning MaintenanceSharpening Cutters Filing Cutter Depth GaugesReplacement Parts and Accessories Technical ServiceRepair Service Replacement ChainsObserved Fault Possible Cause Remedy TroubleshootingRemington Brand Electric Chain SAW Limited Warranties Warranty InformationEnglish Page MODELS/MODELOS/MODÈLES MODELS/MODELOS/MODÈLE Parts LIST/LISTA DE REPUESTOS/LISTE DES PiècesPage Renvoi Pièce DESCRIPTION/DESCRIPCIÓN/DESCRIPTION MODELS/MODELOS/MODÈLES 107625-01, 107625-02MTA Distributors Parts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE PiècesPage 122503-01 Rev. a 03/08

111174-01, 107624-02, 107625-02 specifications

Remington Power Tools has established a strong reputation for providing high-quality outdoor power equipment. Among its notable offerings are the models 107625-02, 107624-02, and 111174-01. Each of these tools is designed to deliver powerful performance, ergonomic design, and innovative technology to meet the diverse needs of homeowners and professional landscapers alike.

The Remington model 107625-02 is a robust gas-powered string trimmer, which stands out for its exceptional cutting capabilities. This trimmer features a 25cc two-cycle engine, providing ample power for tackling thick grass and overgrown weeds. One of the key benefits of this model is its QuickStart technology, which ensures easy starting with minimal effort. Its lightweight design and adjustable handle enhance maneuverability, making it easy to navigate tight spaces. The 107625-02 also includes a bump feed head, allowing users to quickly and efficiently extend the cutting line by simply tapping the head on the ground, a time-saving feature that many users appreciate.

The 107624-02 model is a versatile hedge trimmer that excels in both residential and commercial settings. Powered by a 22cc engine, this tool is engineered to tackle dense hedges and shrubs with precision. One of its standout features is the 24-inch dual-sided blade, designed to provide a clean and precise cut while minimizing the risk of blade binding. Its rotating handle offers enhanced comfort and control, allowing users to trim at various angles without straining their wrists. This hedge trimmer also incorporates anti-vibration technology, making it easier to handle during extended use and reducing operator fatigue.

Finally, the 111174-01 model is a powerful chainsaw that prioritizes both performance and safety. Equipped with a 12-amp electric motor, this chainsaw produces substantial cutting power for felling small to medium trees and performing routine maintenance tasks. It features an automatic oiling system that ensures the chain is consistently lubricated for optimal performance and longevity. The tool's safety features include a chain brake and a safety lock button to prevent accidental starts, making it suitable for both seasoned users and novices alike. Lightweight and easy to handle, the 111174-01 chainsaw is an excellent choice for those looking to maintain their property effortlessly.

Each of these Remington power tools is designed with an emphasis on efficiency, user-friendly features, and durability, making them ideal companions for any outdoor project. Whether you're landscaping your garden or managing a larger property, these tools provide the performance and reliability needed to get the job done right.
Top Page Image Contents