RedMax SRTZ2401 manual Blades MA1, Quick TIP, MA2, Gear Case, Type of Lubricant to be Used

Page 36

MA1

English

9.Maintenance

■BLADES (MA1)

•When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades.

•If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that

they fit more closely together.

1.Loosen lock nut (A) as shown in the diagram.

2.Tighten screw (B) fully, and then turn one-third to one-half of a rotation backward.

3.While holding onto the screw to keep it in position, tighten the lock nut.

4.Check to make sure that the flat washer (C) is loose enough so that it may be turned by pressing on it with a finger.

(1)Upper blade

(2)Lower blade

NOTE

•Screwing in the screw too tightly may make it impossible for the blades to move. Conversely, not screwing in the screw tightly enough may make the blades of the trimmer feel dull and cause leaves and branches to become caught in the blades of the trimmer.

QUICK TIP

If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized RedMax servicing dealer from which you purchased your RedMax trimmer to have the blades resharpened or replaced.

MA2

■GEAR CASE

The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or more often depending on the job condition.

When adding lubricant, use a grease gun to insert lubricant into the three grease nipples located on the gear case. (MA2)

TYPE OF LUBRICANT TO BE USED

Always be sure to use #2 lithium heat-resistant lubricant.

(1) Grease fitting

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents SRTZ2401 Information Informationinformación Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Symbols on the machine PositionEmission Control Emplacement PosiciónControl DE Emisiones Information Importante Concernant LE MoteurFor safe operation Working ConditionWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar EL MotorUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA MachineArranque DEL Motor USO DEL ProductoMaintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up SE1 SE2 Installing HandleAttaching the Trimming Mechanism SE2 Balance UnitAssemblage Montaje Mise EN Place DE LA PoigneeInstalación DEL Mango Equilibrage DE LA MachineWhen using Zenoah genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Operation OP1 OP2 OP3 OP4 Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Ajuste DE LA Velocidad DE Marcha EN Vacío OP6OP7 Adjusting the Angle of the Cutting Blades OP7 Clamp bolt Trimming mechanism Tighten LoosenRéglage DE Langle DES Lames Tranchantes OP7 Boulon de serrage Mécanisme de coupe Serrer DesserrerAjuste DEL Ángulo DE LAS Cuchillas DE CORTE. OP7 Perno de sujeción Mecanismo de poda Ajustar AflojarMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 Blades MA1Quick TIP MA2Entretien Mantenimiento Replacement Plug is a NGK CMR7H MA3 MA4 MA5AIR Filter Fuel FilterFiltre a AIR Filtro DE AireFiltre a Carburant Filtro DE Combustible Bougie D’ALLUMAGE BujíaMuffler MA6 Spark ArresterSpark arrester Intake AIR Cooling VentPARE-ETINCELLES Ouïe DU Refroidissement PAR AIRParachispas Toma DE Aire DE RefrigeraciónProcedures to be Performed After Every 100 Hours of USE StorageMA7 MA8 Cylinder Intake air cooling vent backProcedure a Effectuer Toutes LES 100 Heures D’UTILISATION Rangement AlmacenamientoCylindre Ouïe d’entrée d’air de refroidissement arrière Cilindro Toma de aire de refrigeración posteriorTroubleshooting guide 11. Guía de localización y solución de problemasGuide de localisation des pannes SRTZ2401 NotaParts list Cutting Unit SRTZ2401 S/N Z000001 and up Engine Unit SRTZ2401 S/N 60100101 and up Qty Key# Part Number Description Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC

SRTZ2401 specifications

The RedMax SRTZ2401 is a powerful and versatile tool poised to meet the needs of professionals in the landscaping and horticulture industries. Engineered for efficiency, this two-cycle string trimmer is designed with the user in mind, offering a blend of advanced technologies and features that enhance performance and ease of use.

One of the standout features of the SRTZ2401 is its lightweight design. Weighing in at only 10.4 pounds, it ensures that users can maneuver effortlessly about various job sites, reducing fatigue during prolonged use. This is particularly beneficial for landscaping professionals who require durability without the burden of excess weight.

At the heart of the SRTZ2401 is a 23.9 cc engine that delivers exceptional power and efficiency. This engine not only provides strong performance for cutting through thick grass and weeds but also boasts a fuel-efficient design, allowing for longer run times between refuels. The engine's low emissions meet stringent environmental standards, making the SRTZ2401 an eco-friendly option for professionals.

The SRTZ2401 is equipped with a unique anti-vibration technology that minimizes vibrations throughout the tool. This feature significantly enhances user comfort, allowing for extended periods of use without discomfort or strain. Coupled with an ergonomic handle design, it contributes to a user-friendly experience, keeping fatigue at bay during demanding tasks.

Another notable characteristic of the SRTZ2401 is its innovative cutting head design. It offers a dual-line capability, delivering a cleaner cut while maximizing efficiency. The automatic line feed system ensures hassle-free operation; users can easily replace the line with minimal effort, maintaining productivity throughout the day.

Additionally, the RedMax SRTZ2401 includes an adjustable handle, allowing operators to customize the grip for better control and maneuverability. This feature is crucial for navigating tight spaces and achieving precise cuts in delicate areas.

Overall, the RedMax SRTZ2401 stands out as a top-tier choice for those in need of a reliable, efficient, and powerful string trimmer. Its impressive combination of lightweight construction, robust engine performance, user comfort, and ease of maintenance makes it a valuable addition to any landscaping toolkit. Whether tackling residential lawns or commercial landscapes, the SRTZ2401 promises to deliver consistent results and unmatched reliability.
Top Page Image Contents