RedMax EXZ2401S-BC Maintenance EX2-BC only, EX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1

Page 38

9.Maintenance (EX2-BC only)

EX2-BC MA1

EX2-BC MA2

■REFILLING TRIMMING LINE (MA1)

1.For replacement line, use a diameter of .095in (2.4mm). The spool is capable for a line upto 20ft (6m) on the 4” head. Avoid using a larger line as it may cut down the trimming performance.

WARNING

For safety reasons, do not use metalreinforced line.

2.Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap.

3.Take out the spool and pull off the old line. Fold new line so that one half line is 4.7in.(12cm) shorter than another half.

4.Wind up the line in the correct direction as indicated on the spool.

5.Hook each end of the line in the slot on the edge of the spool, and then put the ends through the eyelets on the housing. Make sure that the spring and the washers are in place.

6.While holding the spool against the housing, pull the line ends to release them from the slot.

7.Line up the slot on the bottom cap with the hook on the housing, press the cap against the housing until it clicks.

■GEAR CASE (MA2)

•The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or more often depending on the job condition.

•Remove the cutter holders before installing new grease to arrange for old grease to exit.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 EX-PS SpecificationsEX-LRT EX-HE 5  Symbols on the machine  6 Working Circumstance For safe operationWorking Condition  7 Working Plan  8  9  Before Starting the EngineStarting the Engine Using the Product  10 Handling Fuel MaintenanceIf Someone Comes  11 Transportation  12 Set up  13 Installing Cutting Head SE2 Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Balance UnitMain pipe Trimming mechanism Screw hole Fastening bolt Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1  15 EX-PS SE2 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE3Hole Moving direction Chain tensioner nut Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6  17 Clamp bolt Lock screw Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 BracketFuel and chain oil When using Zenoah genuine oilHOW to MIX Fuel Recommended Mixing Ratio Gasoline 50OIL 20  Fueling the UnitFor Your Engine LIFE, Avoid Chain OIL EX-PS onlyOperation  21  22  OP6 OP7 OP8Stopping Engine OP6 OP9 Adjusting Throttle CableAdjusting Idling Speed OP10  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 Cutting Method EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle  26 What causes blade thrust EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust  27  28  How you can reduce the chance of blade thrustHow you can maintain the best control  29  EX2-BC OP9 Maintenance BladeTransporting the Unit EX-LRT OP1 Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only Clamp lever Trimming mechanismEX-PS OP1 EX-PS OP2 Checking OIL Supply Adjusting OIL Flow RateOperation EX-PS only  31  32   33  Operation EX-HE onlyEX-HE OP1  34  MaintenanceMaintenance Chart  35  Muffler MA4 36  Spark ArresterMA6 Procedures to be Performed After Every 100 Hours of USEMA51 Cylinder Intake air cooling vent backEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line Gear Case MA2Quick TIP Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Gear CaseGuide BAR Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port  40 SAW Chain EX-PS MA4 MA5 MA6Sprocket EX-PS MA7 MA8 MA9  42  43  Maintenance EX-HE onlyMA1 Gear Case Check Probable Causes Action Troubleshooting guideStorage  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée

EXZ2401S-BC specifications

The RedMax EXZ2401S-BC is a cutting-edge, lightweight brush cutter designed for both professional landscapers and discerning homeowners. Renowned for its power, efficiency, and innovative features, the EXZ2401S-BC is a superb choice for tackling demanding vegetation management tasks with ease.

One of the standout features of the RedMax EXZ2401S-BC is its powerful engine. It is equipped with a robust 24.5 cc two-stroke engine that delivers exceptional torque and speed. This engine is designed to offer impressive cutting performance while maintaining low emissions, complying with stringent environmental standards. The advanced engine technology not only ensures effective operations but also enhances fuel efficiency, allowing users to work for longer periods without frequent refueling.

The design of the EXZ2401S-BC emphasizes user comfort and ease of use. It features an ergonomic handle that provides a secure grip and minimizes vibrations, making it comfortable during extended use. The lightweight construction contributes to reduced fatigue and allows for better maneuverability, ensuring that users can navigate through tight spaces and uneven terrain without difficulty.

In terms of versatility, the RedMax EXZ2401S-BC comes with a dual-line cutting head as standard, which is ideal for trimming grass and light weeds. The capability to interchange between different attachments, such as blades for thicker brush or other cutting tools, enhances its utility. This makes it a multipurpose tool in any landscaping toolkit.

Another notable aspect of the EXZ2401S-BC is its ease of starting. The unit features a reliable starting system that allows for quick and hassle-free ignition. This is particularly important in professional settings where time is of the essence, and projects must adhere to strict deadlines.

Safety is also a priority in the design of the RedMax EXZ2401S-BC. It is equipped with advanced safety features, including a throttle lock that prevents accidental starts and a protective guard around the cutting area, ensuring user protection during operation.

In summary, the RedMax EXZ2401S-BC is a high-performance brush cutter that combines power, versatility, and user-friendly features. With its efficient engine, ergonomic design, and safety enhancements, this brush cutter is ideal for professionals and hobbyists alike, making it a valuable addition to any landscaping arsenal. Whether it's for commercial landscaping or maintaining a residential garden, the EXZ2401S-BC excels in delivering quality performance and reliable service.
Top Page Image Contents