RedMax EXZ2401S-BC Fuel and chain oil, Recommended Mixing Ratio Gasoline 50OIL, HOW to MIX Fuel

Page 19

7. Fuel and chain oil

WARNING

•Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

•The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

•Do not use BIA or TCW (2-stroke water- cooling type) mixed oil.

■RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1

(when using ZENOAH genuine oil)

50:1 MIXING CHART

GASOLINE gal. 1 2 3 4 5

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE

liter

1

2

3

4

5

 

 

 

 

 

 

 

2-CYCLE OIL

ml

20

40

60

80

100

 

 

 

 

 

 

 

•Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

•These engines are certified to operate on unleaded gasoline.

•Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

•If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

•Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

•Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

■HOW TO MIX FUEL

IMPORTANT

Pay attention to agitate carefully.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 848-J8P-93A0 OWNER/OPERATOR ManualContents Safety First 3  Parts locationEX-HE SpecificationsEX-LRT EX-PS 5   6  Symbols on the machine 7  For safe operationWorking Condition Working Circumstance 8  Working PlanStarting the Engine Before Starting the Engine 9   10  Using the Product 11  MaintenanceIf Someone Comes Handling Fuel 12  Transportation 13  Set upBalance Unit Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Installing Cutting Head SE2 15  Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1 Main pipe Trimming mechanism Screw hole Fastening boltEX-PS SE3 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2 17  Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6 Hole Moving direction Chain tensioner nutBracket Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilHOW to MIX Fuel Fuel and chain oilChain OIL EX-PS only Fueling the UnitFor Your Engine LIFE, Avoid  20  21  OperationStopping Engine OP6 OP6 OP7 OP8 22   23  Adjusting Throttle CableAdjusting Idling Speed OP10 OP9 24  Operation EX2-BC only 25  Operation Optional blade usage EX2-BC only 26  EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle Cutting Method 27  EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust What causes blade thrustHow you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  Clamp lever Trimming mechanism Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only EX-LRT OP1 31  Adjusting OIL Flow RateOperation EX-PS only EX-PS OP1 EX-PS OP2 Checking OIL Supply 32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35  Spark Arrester MA4 36  MufflerCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEMA51 MA6Gear Case MA2 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line EX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1Gear Case Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Quick TIP 40  Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port Guide BARSprocket EX-PS MA4 MA5 MA6SAW Chain  42  EX-PS MA7 MA8 MA9MA1 Gear Case Maintenance EX-HE only 43   44  Troubleshooting guideStorage Check Probable Causes ActionEX-LRT ATT EX-PS ATT EX-HE ATT Parts list 46  EXZ-PU S/N 60300000 and up 47   48  EX2-BC S/N 50200000 and up 49   50  Engine Unit 60100000 and upDescription Part Number Qty  51  52  EX-LRT S/N 000531 and upCasing B  53  54  EX-PS S/N 000000 and up 55   56  EX-HE S/N 000101 and up 57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée

EXZ2401S-BC specifications

The RedMax EXZ2401S-BC is a cutting-edge, lightweight brush cutter designed for both professional landscapers and discerning homeowners. Renowned for its power, efficiency, and innovative features, the EXZ2401S-BC is a superb choice for tackling demanding vegetation management tasks with ease.

One of the standout features of the RedMax EXZ2401S-BC is its powerful engine. It is equipped with a robust 24.5 cc two-stroke engine that delivers exceptional torque and speed. This engine is designed to offer impressive cutting performance while maintaining low emissions, complying with stringent environmental standards. The advanced engine technology not only ensures effective operations but also enhances fuel efficiency, allowing users to work for longer periods without frequent refueling.

The design of the EXZ2401S-BC emphasizes user comfort and ease of use. It features an ergonomic handle that provides a secure grip and minimizes vibrations, making it comfortable during extended use. The lightweight construction contributes to reduced fatigue and allows for better maneuverability, ensuring that users can navigate through tight spaces and uneven terrain without difficulty.

In terms of versatility, the RedMax EXZ2401S-BC comes with a dual-line cutting head as standard, which is ideal for trimming grass and light weeds. The capability to interchange between different attachments, such as blades for thicker brush or other cutting tools, enhances its utility. This makes it a multipurpose tool in any landscaping toolkit.

Another notable aspect of the EXZ2401S-BC is its ease of starting. The unit features a reliable starting system that allows for quick and hassle-free ignition. This is particularly important in professional settings where time is of the essence, and projects must adhere to strict deadlines.

Safety is also a priority in the design of the RedMax EXZ2401S-BC. It is equipped with advanced safety features, including a throttle lock that prevents accidental starts and a protective guard around the cutting area, ensuring user protection during operation.

In summary, the RedMax EXZ2401S-BC is a high-performance brush cutter that combines power, versatility, and user-friendly features. With its efficient engine, ergonomic design, and safety enhancements, this brush cutter is ideal for professionals and hobbyists alike, making it a valuable addition to any landscaping arsenal. Whether it's for commercial landscaping or maintaining a residential garden, the EXZ2401S-BC excels in delivering quality performance and reliable service.
Top Page Image Contents