RedMax EXZ2401S-BC manual Maintenance EX-LRT only, EX-LRT MA1 EX-LRT MA2 Blades MA1, Quick TIP

Page 39

9.Maintenance (EX-LRT only)

EX-LRT MA1

EX-LRT MA2

■BLADES (MA1)

•When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades.

•If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together.

1.Loosen lock nut (A) as shown in the diagram.

2.Tighten screw (B) fully, and then turn one- third to one-half of a rotation backward.

3.While holding onto the screw to keep it in position, tighten the lock nut.

4.Check to make sure that the flat washer (C) is loose enough so that it may be turned by pressing on it with a finger.

(1)Upper blade

(2)Lower blade

NOTE

Screwing in the screw too tightly may make it impossible for the blades to move. Conversely, not screwing in the screw tightly enough may make the blades of the trimmer feel dull and cause leaves and branches to become caught in the blades of the trimmer.

QUICK TIP

If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized RedMax servicing dealer from which you purchased your RedMax® trimmer to have the blades resharpened or replaced.

■GEAR CASE

The reduction gears are lubricated by multipurpose, lithium-based grease in the gearcase.

Supply new grease every 25 hours of use or more often depending on the job condition.

When adding lubricant, use a grease gun to insert lubricant into the three grease nipples located on the gear case. (MA2)

(1) Grease fitting

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 848-J8P-93A0 OWNER/OPERATOR ManualContents Safety First 3  Parts locationEX-HE SpecificationsEX-LRT EX-PS 5   6  Symbols on the machine 7  For safe operationWorking Condition Working Circumstance 8  Working PlanBefore Starting the Engine Starting the Engine 9   10  Using the Product 11  MaintenanceIf Someone Comes Handling Fuel 12  Transportation 13  Set upBalance Unit Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Installing Cutting Head SE2 15  Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1 Main pipe Trimming mechanism Screw hole Fastening boltEX-PS SE3 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2 17  Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6 Hole Moving direction Chain tensioner nutBracket Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilHOW to MIX Fuel Fuel and chain oilChain OIL EX-PS only Fueling the UnitFor Your Engine LIFE, Avoid  20  21  OperationOP6 OP7 OP8 Stopping Engine OP6 22   23  Adjusting Throttle CableAdjusting Idling Speed OP10 OP9 24  Operation EX2-BC only 25  Operation Optional blade usage EX2-BC only 26  EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle Cutting Method 27  EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust What causes blade thrustHow you can reduce the chance of blade thrust How you can maintain the best control 28  EX2-BC OP9 Maintenance Blade Transporting the Unit 29  Clamp lever Trimming mechanism Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only EX-LRT OP1 31  Adjusting OIL Flow RateOperation EX-PS only EX-PS OP1 EX-PS OP2 Checking OIL Supply 32  Operation EX-HE only EX-HE OP1 33  Maintenance Maintenance Chart 34   35  Spark Arrester MA4 36  MufflerCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEMA51 MA6Gear Case MA2 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line EX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1Gear Case Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Quick TIP 40  Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port Guide BAREX-PS MA4 MA5 MA6 SprocketSAW Chain  42  EX-PS MA7 MA8 MA9Maintenance EX-HE only MA1 Gear Case 43   44  Troubleshooting guideStorage Check Probable Causes ActionEX-LRT ATT EX-PS ATT EX-HE ATT Parts list 46  EXZ-PU S/N 60300000 and up 47   48  EX2-BC S/N 50200000 and up 49   50  Engine Unit 60100000 and upDescription Part Number Qty  51  52  EX-LRT S/N 000531 and upCasing B  53  54  EX-PS S/N 000000 and up 55   56  EX-HE S/N 000101 and up 57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée

EXZ2401S-BC specifications

The RedMax EXZ2401S-BC is a cutting-edge, lightweight brush cutter designed for both professional landscapers and discerning homeowners. Renowned for its power, efficiency, and innovative features, the EXZ2401S-BC is a superb choice for tackling demanding vegetation management tasks with ease.

One of the standout features of the RedMax EXZ2401S-BC is its powerful engine. It is equipped with a robust 24.5 cc two-stroke engine that delivers exceptional torque and speed. This engine is designed to offer impressive cutting performance while maintaining low emissions, complying with stringent environmental standards. The advanced engine technology not only ensures effective operations but also enhances fuel efficiency, allowing users to work for longer periods without frequent refueling.

The design of the EXZ2401S-BC emphasizes user comfort and ease of use. It features an ergonomic handle that provides a secure grip and minimizes vibrations, making it comfortable during extended use. The lightweight construction contributes to reduced fatigue and allows for better maneuverability, ensuring that users can navigate through tight spaces and uneven terrain without difficulty.

In terms of versatility, the RedMax EXZ2401S-BC comes with a dual-line cutting head as standard, which is ideal for trimming grass and light weeds. The capability to interchange between different attachments, such as blades for thicker brush or other cutting tools, enhances its utility. This makes it a multipurpose tool in any landscaping toolkit.

Another notable aspect of the EXZ2401S-BC is its ease of starting. The unit features a reliable starting system that allows for quick and hassle-free ignition. This is particularly important in professional settings where time is of the essence, and projects must adhere to strict deadlines.

Safety is also a priority in the design of the RedMax EXZ2401S-BC. It is equipped with advanced safety features, including a throttle lock that prevents accidental starts and a protective guard around the cutting area, ensuring user protection during operation.

In summary, the RedMax EXZ2401S-BC is a high-performance brush cutter that combines power, versatility, and user-friendly features. With its efficient engine, ergonomic design, and safety enhancements, this brush cutter is ideal for professionals and hobbyists alike, making it a valuable addition to any landscaping arsenal. Whether it's for commercial landscaping or maintaining a residential garden, the EXZ2401S-BC excels in delivering quality performance and reliable service.
Top Page Image Contents