RedMax EXZ2460S-PH HE-EX MA1, RMS-EX MA1, End cap, Main gear, Replacing the Gearcase OIL MA1

Page 27

EXZ2460S-PH

9. Maintenance

HE-EX MA1

(HE-EX2 only)

GEAR CASE

• The reduction gears are lubricated by

multipurpose, lithium-based grease in

the gear case. At every 20 hours of

RMS-EX MA1

3. Place the RedMax Sweeper main gear flat. Refill the gearcase with Mobil SHC 634 Synthetic Gear Oil to the top of the main gear (60ml – 1.80zs), as shown.

DO NOT OVERFILL! (MA1)

U

use, supply the gear case with new

grease.

(1) End cap

S

• Remove the cutter holders before

installing new grease to arrange for old

grease to exit.

NOTE

When removing and installing the cutter holder(a), use care not to allow any dirt and dust entering in to the gear case.

(2) Main gear

4.Apply a continuous bead of loctite ultra grey around the pilot diameter of the end cap. Install the end cap, and then install and firmly tighten the four end cap bolts.

5.Install the drum and axle assemblies, and then reconnect the spark plug wire.

(RMS-EX only)

GEARCASE LUBRICATION With the exception of oil leaks or contamination, the RedMax Sweeper's oil filled gearcase is designed to last the life of the machine under normal use:

It is not necessary to add oil or to "top off" the gearcase under normal operating conditions.

For continuous heavy-duty applications, (such as where the machine will be stopped only during refueling), RedMax recommends replacing RedMax Sweeper gearcase oil every 40 hours of operation.

REPLACING THE GEARCASE OIL (MA1)

Warm the gearcase oil by running the RedMax Sweeper at varying speeds for approximately 8-10 minutes, and then switch the engine to "OFF" and disconnect the spark plug wire at the engine. Use the following procedure to remove and replace all gearcase oil.

1.Remove the drum and axle assemblies (see page 12), and then remove the four end cap bolts and the end cap (the gearcase need not be removed from the RedMax Sweeper).

2.Allow all used gearcase oil to drain into a small container.

WARNING

BURN DANGER! The gearcase and oil will be extremely hot after use!

IMPORTANT

Use only Mobil SHC 634 Synthetic Gear Oil.

Do not mix other oils ar additives with the RedMax Sweeper Gearcase Oil.

Do not disturb the sealed end plug or bolt on the gearcase (leakage may occur).

Do not use the RedMax Sweeper if oil is leaking from the gearcase. Return the machine to the dealer for repairs.

WARNING

Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving sweeping head or hot muffler may result in a personal injury.

US-27

Image 27
Contents EXZ2460S-PH Contents BC-EX3 LRT-EX3 PS-EX HE-EX2 Parts locationRMS-EX SpecificationsLRT-EX3 PS-EXSymbols on the machine Emission ControlManufactured For safe operation Using the product Before useStarting the engine Transport Fuel safetyAvoid noise problem MaintenanceDisposal Set up PS-EX SE2 Attaching the Pruning Mechanism SE1 PS-EX SE3 PS-EX SE4PS-EX SE1 PS-EX SE5 PS-EX SE6Sweeper Assembly SE1 HE-EX2 SE1HE-EX2 SE2 RMS-EX SE1 Gasoline Requirements WarrantyFuel and Chain Oil FuelChain OIL HOW to MIX Fuel Recommended Mixing Ratio Gasoline 50 OILFor Your Engine LIFE, Avoid Fueling the UnitOperation OP7 Adjusting Throttle CableAdjusting Idling Speed OP8 Adjusting the Line LengthOperation BC-EX3 only Optional blade usage Controlling Blade Thrust OPT8 OPT9 Starting the EngineCutting Method OPT1122, 24-tooth blade Tooth blade Point OPT12 Maintenance BladeHow you can maintain the best control OPT12Checking OIL Supply Adjusting OIL Flow RateAdjusting the Angle of the Cutting Blades OP1 PS-EX OP1Properly Dressed Operator OP1 Direction of rotationBREAK-IN Operation HE-EX2 OP1 RMS-EX OP1RMS-EX OP5 Operating and Safety Tips OP5General Safety Instructions RMS-EX OP2 RMS-EX OP3 Operating Techniques OP2OP3OP4Spark Plug MaintenanceMaintenance Chart MA1 AIR Filter MA3 MA4 Procedures to be Performed After Every 100 Hours of USE Muffler MA5LRT-EX3 MA1 Blades MA1BC-EX3 MA1 Refilling Trimming Line MA1PS-EX MA2 PS-EX MA3 PS-EX MA4 PS-EX MA5 Guide BAR PS-EX MA1Oiling Port PS-EX MA6Main gear HE-EX MA1RMS-EX MA1 End capCase 1. Starting failure Troubleshooting guideStorage DisposalWhat is Covered Manufacturers Warranty CoverageOwners Warranty Responsibilities Warranty Commencement DateWhere to GET Warranty Service Emission Warranty Parts ListWhat is not Covered HOW to File a Claim