RedMax EXZ2500S-BC manual Operation EX-HE only, EX-HE OP1,  34 

Page 34

8. Operation (EX-HE only)

EX-HE OP1

WARNING

•Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

•Keep the blade guard and the mad guard attached in place at all times when the unit is operated.

•Before starting a job, check the area and remove all obstacles and objects that could be thrown by the blade.

•Do not adjust the wheel height or try to remove anything entangled to the blade with the engine running.

1.Before starting the engine, adjust the wheel height for desired cutting depth (See page 22).

2.Before starting a job, plan your direction of travel so that you can always hold the edger on you right side and can walk on a hard surface as much as possible.

3.When starting to edge, run the engine at full throttle, and slowly have the blade cut into the edge groove.

NOTE

•Do not use the EX-HE to make a new groove into the ground. Such usage will not be covered by RedMax Warranty.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents OWNER/OPERATOR Manual T3087-93110Page Safety First ContentsParts location  4 EX-LRT SpecificationsEX-BC EX-PS 6  Type de moteur 1KZXS.0254QR EM Cylindrée du moteur 25,4cc Symbols on the machine 7  Working Circumstance For safe operationWorking Condition  8 Working Plan  9 Starting the Engine Before Starting the Engine 10  Using the Product  11 Handling Fuel MaintenanceIf Someone Comes  12 Transportation  13 Set up Debris guard Plate Screw EX-BC SE1 SE2 Installing Debris GuardInstalling Cutting Head SE2 EX-BC SE3 Balance UnitMain pipe Trimming mechanism Screw hole Fastening bolt EX-LRT SE1 Attaching the Trimming Mechanism SE1 16  EX-PS SE3 EX-PS SE1 Attaching the Pruning Mechanism SE1EX-PS SE2  17 Hole Moving direction Chain tensioner nut Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6  18 Bracket EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4Clamp bolt Lock screw  19 Recommended Mixing Ratio Gasoline 50OIL HOW to MIX FuelFuel  20 For Your Engine LIFE, Avoid Fueling the Unit 21  Operation  22 Stopping Engine OP6 OP6 OP7 OP8 23  OP9 Adjusting Throttle CableAdjusting Idling Speed OP10  24 Trimming Grass and Weeds Adjusting the Line LengthEX-BC OP1 Cutting Work Line Head Usage  25  26  Cutting Method EX-BC OP4 EX-BC OP5 EX-BC OP6Bracket Handle  27 Operation EX-BC OP7 EX-BC OP8 28  Controlling Blade BounceHow you can maintain the best control How you can reduce the chance of kick out 29  Transporting the Unit EX-BC OP9 Maintenance Blade 30  EX-LRT OP1 Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only Clamp lever Trimming mechanismEX-PS OP1 EX-PS OP2 Checking OIL Supply Adjusting OIL Flow RateOperation EX-PS only  32  33  EX-HE OP1 Operation EX-HE only 34  Maintenance Chart Maintenance 35   36  Spark arrester MA4 MufflerSpark Arrester Intake AIR Cooling VentMA6 Procedures to be Performed After Every 100 Hours of USEMA51 Cylinder Intake air cooling vent backGear Case MA5 Maintenance EX-BC onlyFor safety reasons, do not use metalreinforced line  39 Blades MA1 EX-LRT MA1 EX-LRT MA2 40  Quick TIPGuide BAR Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port  41 Sprocket EX-PS MA4 MA5 MA6 42  SAW ChainEX-PS MA7 MA8 MA9  43 MA1 Gear Case Maintenance EX-HE only 44  Storage  45 Check Probable Causes Action Troubleshooting guide 46  Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 302845 and up  48  49  EX-BC S/N 302960 and up  50  51  Engine Unit 352001 and up  52  53  Description Part Number QtyEX-LRT S/N 000531 and up  54  55  Casing BEX-PS S/N 000000 and up  56  57  EX-HE S/N 000101 and up  58  59  Manufacturer’s warranty coverage RedMax 2-YEAR Limited Warranty RedMax Garantie limitée à 2 ans Page Komatsu Zenoah America INC
Top Page Image Contents