Troubleshooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-877-897-7493, Monday through Friday, 8 a.m. until 5 p.m. Central Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter from the filter housing and clean or replace the filter (see page 13).

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS, BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. The water will heat at a rate of 6°F per hour. If you are using the spa indoors and the room temperature is main- tained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set temperature.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature	Heating Time
70°F +	6 to 8 hours
50°F to 70°F	9 to 11 hours
30°F to 50°F	12 to 14 hours

b. If the water still has not heated after four days, contact our customer service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter are in place. Clean the filter if they are dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly. See the section on maintain- ing the proper pH balance on page 13.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.This usually occurs only when the water level is low. Add water until it is 2 to 4” above the skim- mer basket.

b.The filter cover may not be tight. Make sure the filter cover is tight.

9.SYMPTOM: THE WATER LEVEL DROPS

a.A clamp or seal inside the pump compartment may be loose. Check inside the pump compart- ment for excess water and watch the pump unit while it is operating to see if water drips from any of the plumbing. If you can identify the location of the leak inside the spa jet unit, tight- en the clamp or replace the damaged seal.

b.Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, the spa shell may have a leak. Contact your local pool and spa service provider for repairs.

PFSB62830 specifications

The ProForm PFSB62830 is a versatile and efficient exercise bike designed for those who are serious about their fitness journey. This model provides a blend of innovative technology and user-friendly features that make it suitable for both beginners and seasoned athletes seeking to enhance their indoor cycling experience.

One of the standout features of the ProForm PFSB62830 is its robust construction. The bike comes with a solid steel frame that ensures stability and durability, making it capable of supporting varied body types and intensities of workouts. With an adjustable seat and handlebars, users can easily customize their riding position for maximum comfort during extended sessions.

The PFSB62830 is equipped with a smooth and quiet magnetic resistance system. This technology allows users to enjoy a nearly silent workout experience, which is perfect for home settings where noise may be a concern. The bike offers multiple resistance levels, providing a tailored workout that can continuously challenge beginners and advanced riders alike.

Integrated into the bike's design is a user-friendly console that displays essential workout metrics such as time, speed, distance, and calories burned. This real-time feedback helps users track their progress and stay motivated throughout their fitness journey. While the bike is efficient for physical activity, it's also equipped to accommodate interactive workouts through compatibility with various fitness apps, promoting a more engaging exercise experience.

Another impressive feature is the ProForm's compact design. Fitting seamlessly into smaller spaces, the bike is often equipped with transport wheels for easy mobility, allowing users to store it away when not in use. This practicality, combined with a sleek aesthetic, makes it a visually appealing addition to any home gym.

In conclusion, the ProForm PFSB62830 stands out for its exceptional build quality, seamless user experience, and adaptability to different fitness levels. Its combination of advanced resistance technology, real-time data tracking, and ease of use makes it a fantastic option for anyone looking to elevate their indoor cycling workouts. Whether you're a beginner easing into fitness or an experienced cyclist, this exercise bike promises to deliver a reliable and motivating workout experience.