Adams 22 Check the Level of CUT, Folding Handle Storage, HOW to Prepare the Mower, For Storage

Page 17

MAINTENANCE

5.Make sure the blade is balanced. Use a screwdriver and hold the blade parallel to the ground as shown. A blade that is bal- anced will stay parallel to the ground. If the blade is not balanced, the heavy end will rotate toward the ground. Sharpen the heavy end until the blade is balanced.

6.A new blade will cut better than a badly worn blade. Every two years replace the old blade with a factory replacement blade.

CHECK THE LEVEL OF CUT

Test the unit in a small area. If the height of cut is not level or if the cut grass is not discharged, the cause can be: (1) the blade is bent or dam- aged, (2) the blade is not sharp, (3) a worn blade, (4) or a broken blade adapter. Before you use the unit, correct the problem.

FOLDING HANDLE STORAGE

CAUTION: Be careful when you fold or raise the handle. Do not damage the cables. A cable that is bent will not work correctly. Before you use the unit, replace a bent or damaged cable.

How To Fold The Handle

1.Loosen the knobs that hold the upper part of the handle to the lower part of the han- dle. As you fold the handle, make sure the cables are not around the loose fasteners and do not become damaged. Hold the en- gine stop lever in the Operating Position (against the handle). Rotate the upper part of the handle toward the back of the unit (Figure 15) .

2.Loosen the knobs on the lower handle (Figure 16). Push in on the ends of the lower handle. Move the ends of the lower handle past the locking tabs.

3.Rotate the handle forward over the en- gine. Make sure the cables are not dam- aged.

Recoil-Start Rope

Push in on

lower handle.

Figure 15

Lower Handle

Locking

Tabs

Knob

Figure 16

How To Raise The Handle

1.Pull the handle back until the ends of the lower handle lock into position.

2.Hold the engine stop lever in the Operating Position (against the handle). Lift the up- per part of the handle into the operator’s position. Tighten the fasteners that hold the handle.

3.Make sure the recoil-start rope is on the outside of the handle and is not caught be- tween the upper and lower handle.

HOW TO PREPARE THE MOWER

4. Remove the spark plug from the cylinder.

FOR STORAGE

Pour one ounce of oil into the cylinder.

 

Slowly pull the recoil-start grip so that the

WARNING: Do not remove gaso-

oil will protect the cylinder. Install a new

line while inside a building, near

spark plug in the cylinder.

afire, or while you smoke. 5. Clean the dirt and debris from the cylinder

Gasoline fumes can cause an explosion or

 

cooling fins and the engine housing.

a fire.

6.

Clean the bottom of the mower housing.

1.

Drain the fuel tank.

7.

Completely clean the mower to protect the

2.

Let the engine run until it is out of gasoline.

 

paint.

3.

Drain the oil from the warm engine. Fill the

8.

Put the unit in a building that has good ven-

 

engine crankcase with new oil.

17

tilation.

F-050414L

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Models MURRAY, INC. Two Year Limited Warranty Responsibility of the Owner OWNER’S InformationII. Slope Operation Safe Operation Practices for Walk-Behind MowersGeneral Operation III. Children IV. ServiceUse only original equipment or authorized replacement parts Tices. Read the next few pages carefully Safe Mowing GuideThey can help you learn. Too often the mow Read this Instruction Book. ReadAdjustment,except carburetor, while the en Make the clean up after mowing easierAccessory and the mower Bruises, or even put out an eye. Often the perSional service, select a shop that is an Stitutions as service parts. If you need profesAuthorized Service Center for your brand Mower. If you plan to service the unit yourselfBefore using the grass catcher again Ufacturer’s recommended replacement partWhen the front of the mower has come up Cause. Vibration is generally a warningAfter Mowing Steps to Follow Before MowingWhile Mowing Unpacking Instructions PreparationHandle Remove the washers and axle knobsHigh Position Handle BracketHandle LOW PositionFinal Assembly HOW to Prepare the EngineHOW to Start Engine HOW to Stop the EngineOperation Engine Stop LeverEngine Maintenance MaintenanceHOW to Clean HOW to Adjust Mower Housing Height of CUT LubricationHOW to Remove the Blade Blade ServiceHOW to Sharpen the Blade Check the Level of CUT HOW to Prepare the MowerFolding Handle Storage For StorageTrouble Shooting Chart 050414L KEY Description Handle Briggs & Stratton ModelsHandle Tecumseh Engine Models Models with Standard Wheels 1101302E700 1101303E700Wheel Size & Type Wheels and Tires050414L 050414L 050414L MURRAY, INC. Lawn Mower Central Parts Distributors HOW to Order Repair Parts

22 specifications

Adams 22 is a cutting-edge software platform designed to streamline and enhance the management of complex systems in various industries. Known for its versatility and robustness, Adams 22 offers a comprehensive suite of features that cater to the needs of engineers, designers, and project managers.

One of the standout features of Adams 22 is its advanced modeling capabilities. The platform allows users to create highly detailed and accurate simulations of mechanical systems. This includes the ability to model both rigid and flexible bodies, enabling engineers to analyze how components interact under various conditions. The software supports state-of-the-art visualization tools, allowing teams to view, manipulate, and understand complex systems in real time.

Adams 22 also excels in its integration with other engineering software. It seamlessly connects with CAD applications, enabling users to import designs directly into the simulation environment. This integration reduces errors and accelerates the design process, as engineers can quickly test and iterate on their models without the need for extensive rework.

Another key characteristic of Adams 22 is its powerful simulation algorithms. The platform employs advanced numerical methods to solve dynamic equations, providing users with accurate and reliable results. This consistency is vital for engineering applications where precision is crucial, such as in automotive and aerospace industries. Additionally, Adams 22 incorporates various solver options, allowing users to choose the best approach for their specific simulation needs.

User-friendliness is also a hallmark of Adams 22. The intuitive interface is designed to cater to both novice and experienced users, facilitating a smooth learning curve. Comprehensive documentation and a supportive community foster an environment conducive to knowledge sharing and collaboration.

The software also includes robust optimization tools, which enable users to fine-tune their designs for performance, weight, and cost. By leveraging advanced algorithms, Adams 22 helps engineers identify the best design alternatives, enhancing the efficiency of the development process.

In summary, Adams 22 is a versatile and powerful platform that transforms the way engineers and designers approach complex simulations. With its innovative features, seamless integration, and user-friendly design, it stands out as a vital tool for modern engineering applications. As industries continue to evolve, Adams 22 remains at the forefront, providing the technologies necessary to meet the challenges of tomorrow.
Top Page Image Contents